In my setup, I have an on-prem environment that is connected to my Azure environment using S2S VPN connection. We, developers, use P2S connection to access Azure environment.
Our setup looks like on the image below:
We'd also like to access on-prem resources, however that only works when BGP is enabled. Would it be possible to somehow manually adjust routes, so that we do not need to enable BGP ? If yes, how can I do that ?
We'd also like to access on-prem resources, however that only works when BGP is enabled. Would it be possible to somehow manually adjust routes, so that we do not need to enable BGP ? If yes, how can I do that ?
Unfortunately, there’s no workaround to connect to your Site-to-Site VPN from your Point to Site VPN connected to same V-net without BGP.
You can use BGP and route your traffic to communicate between your On-prem site connected to S2S and your client machines connected via P2S to Azure V-Net.
The Clients can only connect to Vnet without BGP, and the client can connect to on prem Site given S2S has BGP enabled.
References:
Azure VPN Gateway: About P2S routing - Azure VPN Gateway | Microsoft Learn
Azure routing | from p2s client VPN to s2s network on-prem - Microsoft Q&A by Sai Kishore
Related
I have been trying to tackle a problem where I need to create a second VPN tunnel to a site (SiteA), this site already has a VPN tunnel set up with our VPN Gateway.
SiteA is unable to create a second tunnel to our VPN gateway public IP, as a route already exists.
I need to knnow can I add a second IP to the vPN gateway, which I think is a NO, but I can't find anything concrete to validate that, and if that's not possible, can we add a second VPN gateway into the same GatewaySubnet, in our hub vNET.
Although I think this would be problematic as how would the traffic from firewall know which tunnel to send the taffic to.
Some backgound: Hub and spoke design with hub consisting of Az firewall and Az VPN gateway. Peered spokes route through FW to get to VPN gateway. Hope that makes sense.
Thanks in advance.
To create a second VPN tunnel to a site (SiteA), which already has a VPN tunnel set up with your VPN Gateway, you can enable your Azure VPN gateway for an active-active configuration, where both instances of the gateway VMs will establish S2S VPN tunnels to your on-premises VPN device, as shown in the following diagram:
Refer : https://learn.microsoft.com/en-us/azure/vpn-gateway/vpn-gateway-highlyavailable#active-active-vpn-gateways
In the Active-active Azure VPN gateway configuration, each Azure gateway instance will have a unique public IP address, and each will establish an IPsec/IKE S2S VPN tunnel to your on-premises VPN device specified in your local network gateway and connection. You will need to configure your on-premises VPN device to accept or establish two S2S VPN tunnels to the two Azure VPN gateway public IP addresses which are created when active-active option is enabled and because the Azure gateway instances are in active-active configuration, the traffic from your Azure virtual network to your on-premises network will be routed through both tunnels simultaneously, even if your on-premises VPN device may favor one tunnel over the other.
To change/update an existing Azure VPN gateway from active-standby to active-active mode, refer the below doc:
https://learn.microsoft.com/en-us/azure/vpn-gateway/active-active-portal#-update-an-existing-vpn-gateway
Is there a VPN solution in Azure that can assign a static public IP to the clients connected for me to achieve full tunnelling? may be in P2S VPN?
P2S VPN does not have full tunneling. Is there any other alternate solution?
• No, you can’t assign a static public IP address to the clients for a VPN solution in Azure as the client address pool that needs to be defined while deploying a VPN gateway in Azure is a subnet of the IP address spaces that the virtual network is created out of.
But you can configure forced tunnelling in your Azure virtual network on your VPN gateway subnets as illustrated below. In the below image, forced tunnelling is shown for Site-to-Site VPN scenario but it can also be implemented for Point-to-Site VPN scenarios in the same way. The Frontend subnet is not force tunneled. The workloads in the Frontend subnet can continue to accept and respond to customer requests from the Internet directly. The Mid-tier and Backend subnets are forced tunneled. Any outbound connections from these two subnets to the Internet will be forced or redirected back to an on-premises site via one of the Site-to-site (S2S) VPN tunnels as shown below.
This allows you to restrict and inspect Internet access from your virtual machines or cloud services in Azure, while continuing to enable your multi-tier service architecture required. If there are no Internet-facing workloads in your virtual networks, you also can apply forced tunneling to the entire virtual networks.: -
• Also, please note that you can *configure the above for your P2S clients by securing the Internet traffic via Firewall Manager and advertising the 0.0.0.0/0 route to your VPN clients. This makes your clients send all internet bound traffic to Azure for inspection. Then, firewall SNATs the packet to the PIP of Azure Firewall for egress to Internet. For this purpose, setup the Azure Firewall Policy to allow P2S traffic to Internet and to advertise all the traffic from 0.0.0.0/0 to your VPN clients, you would need to break them into two smaller subnets 0.0.0.0/1 and 128.0.0.0/1 as mentioned in the below documentation: -
https://learn.microsoft.com/en-us/azure/vpn-gateway/vpn-gateway-p2s-advertise-custom-routes#forced-tunneling
Also, you can add the code below in your ‘azurevpnconfig.xml’ file that can be directly downloaded from the templates section if the above said subnets cannot be added in ‘Default Routes’ on the portal.
<clientconfig>
<includeroutes>
<route>
<destination>0.0.0.0</destination><mask>1</mask>
</route>
<route>
<destination>128.0.0.0</destination><mask>1</mask>
</route>
</includeroutes>
</clientconfig>
My VNet won't allow me to connect to the s2s location via p2s connection.
I'm trying to connect the Azure VPN client on my machine and reach a site that is allowed in a network which I have a s2s connection to.
Here's the thing, I can't get traffic to flow from my pc running the VPN client, out to the target site.
Topology
PC > VPN Client > VNet via p2s > Remote network via s2s > FTP server
I'd like to be able to ping the FTP server from my machine.
Currently only devices in the VNet can ping.
I tried setting up BGP but it broke the connection, as I don't really know how things should be set.
I don't have access to the remote site or it's devices.
I have a Azure local network gateway which is configured as the s2s location.
I'm sorry if that doesn't make sense.
Edit: here is the picture of the network
BGP is the standard routing protocol which enables the Azure VPN Gateways and your on-premise VPN devices to exchange "routes" that will inform both gateways on the availability and reachability for those prefixes to go through the gateways or routers involved.
To configure the BGP, your on-premise device should also support BGP. Read
What address does Azure VPN gateway use for BGP Peer IP?
What are the requirements for the BGP Peer IP addresses on my VPN device?
What should I specify as my address prefixes for the Local Network Gateway when I use BGP?
Without BGP, If you add the point-to-site addresses after you create your site-to-site VPN connection, you need to update the routes manually. You need to manually add the routes to the remote network on your machine.
For more information, you could refer to configure and validate virtual network or VPN connections. Except the Ping tool, you prefer to use TCping tool, see the detailed steps.
Generally, you could troubleshoot the issue by searching the common issue and solution in the virtual network gateway---Diagnose and solve problems on Azure portal. It's recommended to new a support ticket to get your issue resolved quickly.
My solution to this as I can't enable BPG is to use a proxy server within the VNet.
I deployed an openvpn virtual appliance and clients can reach peered networks, the VNET of the appliance itself, but not the network onpremise that is reachable via the virtual network gateway (routed VPN). When I use the P2S OpenVPN provided from Azure clients can reach onpremise network. What am I missing ?
I deployed an OpenVPN appliance because Azure OpenVPN lacks ccd support.
I solved the problem by adding the OpenVPN client IP range to the VNET address space. I then created a subnet with the same IP range. Obviously, you can't put any resource in this subnet. By then adding this subnet to the route, OpenVPN clients could traverse the gateway.
After my test on my windows client, I can directly access the on-premise network from the Azure VPN gateway based VNet or access the resources in the VPN based VNet from the on-premise network. You could follow these tutorials:
Configure a Point-to-Site connection to a VNet using native Azure certificate authentication: Azure portal
Set up OpenVPN® Protocol on Azure VPN Gateway.
Configure OpenVPN clients for Azure VPN Gateway
I have not deployed an OpenVPN virtual appliance, but I think it will be something like this: Point-to-Site (P2S) connection using OpenVPN infrastructure
According to this quick start, If you use a virtual VPN appliance, It is necessary to create a routing table on Azure so that traffic to your VPN subnet is directed back to your VPN instance and enable IP forwarding for this network interface. You could get more details about custom routes.
Feel free to let me know if I am misunderstanding you.
I have a couple of queries about Azure VNet to On-Premises Site-to-Site networking -
As per Azure, Site-to-Site connection between On-Premises and Azure VNet should have a VPN tunnel. For this to happen there should be a VPN supported device at On-Prem and also a VPN Gateway at VNet. Is my understanding correct ?
Secondly, if a custom device capable of VPN functionality is deployed at On-Prem as well as a VM in Azure VNet, can they establish a connection between them without default Azure provided Site-to-Site VPN tunnel ? Is it possible to establish a network in Site-to-Site without VPN tunnel like with just igw's(Internet Gateways in AWS Cloud)?
What is the significance of next hop being "Internet" in azure route table ?
Yes. This device should also have a real external ip address, not behind the NAT.
Yes, you could use, say, Sophos to create VPN without using Azure's default VPN.
Internet. Represents the default Internet gateway provided by the Azure Infrastructure. (https://azure.microsoft.com/en-us/documentation/articles/virtual-networks-udr-overview/)