I'm creating a setup with Inno Setup. This setup adds files to a "main program" and after installing some files it runs another custom program which kind of unpacks some previously installed files.
This unpacking program relies on some existing files being writable, which usually is the case. But on development machines these files are under version control and therefore write protected (have read-only attribute).
The unpacking program just doesn't unpack when these files are write protected (maybe it shows a warning in the console, but the console is hidden so one won't see this warning). And I can't change the code of this unpacking program.
So, I'm looking for a way to make these files writable with Inno Setup even though these files are not installed by Inno Setup.
How can I achieve this?
There's no built-in mechanism for that in Inno Setup.
But you can do almost anything from Pascal Script using WinAPI. In this case, you want to use SetFileAttributes.
For an example how to use SetFileAttributes from Inno Setup, see:
Inno Setup Code section create hidden file
Related
I have a set of files (scenery data of an airport) that should be installed to one of several applications (3 different flight simulators) depending on the target applications being installed. If more than one is installed, the user has to choose into what application the set of files should be installed.
Of course I could write for each application a separate installer but that would make it awkward to maintain and blow up the number of installers since there are many sets of files to install.
Problem is that depending on the chosen application the AppId, the installation destination and other installation values changes.
I intend to write a custom wizard page that is shown immediately after the welcome page to find out which of the target applications are installed and let the user choose the required application in case there are several installed.
My current problem is that the files to copy are not fully the same for each possible application. So I need in the [Files] section the posibility to copy a file to its target location depending on the application selected. I hoped to find a general parameter for the [Files] section that could be used to copy or not. But I could not find one. How could I solve this problem? I also studied [Components] and [Tasks] to find a solution but was not successful.
Thanks for any hint how to solve my problem!
To answer your literal question: Use Check parameter to bind [Files] (and other) section entries to the selection on the custom page.
Some examples:
Inno Setup - Multiple software versions in one installation
How to install only file based on condition (external configuration file) in Inno Setup
Conditional file copy in Inno Setup
Inno Setup: How to auto select a component by comparing a register key version?
Though you also might consider using a preprocessor to easily maintain and auto-generate multiple installers from same source script.
For an example, see:
Compile Inno Setup installer for specific component only
I have four installers built with separate .iss files: client installer, server installer, client update installer, server update installer. At the moment I use separate isl files for each installer.
My question is can I use Inno Setup preprocessor inside the isl file to decide which messages refer to which installer so I could use only one instance of isl file for each language?
You can use a preprocessor in .isl files, only if you use a hack like this one from your previous question: Full preprocessor support in Inno Setup language files (isl)
When you do, you can use /D switch on the commandline of the iscc process that preprocesses the .isl files (in the PreprocessLanguage macro). Use the variable to identify your build. And you can then use the variable in your .isl files any way you like. You already know how: How can I pass command line parameters with a value to the Inno Setup Compiler, so I can use them in my code?
I try to make a setup with Inno Setup for my program.
I have installed more file XML in the same folder as the .exe. The install work well, but when I run the program and modify the XML, the file is saved in another place, not the folder of the .exe and I can't find it. I think the file is stored in the PC because the program can open it without problems.
I also try to make the same setup with InstallAware Express 7 and it works well. Io I think it's not a problem in my exe but in Inno Setup.
Thanks
I think you are a victim of Windows File virtualization.
You probably install data files to Program Files folder.
That folder is not writable (unless your program runs with elevated privileges). If your program does not have application manifest, Windows considers it a legacy application that is not aware of its inability to write to Program Files and enables file virtualization. So, when your application tries to write the data/XML files, Windows redirects the write (and future reads) to a virtual store (C:\Users\username\AppData\Local\VirtualStore). The actual files in the Program Files are not modified.
It's difficult to answer, why it works with the InstallAware Express. If you tried it after the Inno Setup, the results can be affected by an existence of the file in the virtual store.
Anyway, the root cause is that your application tries to write the files in the Program Files. That's just wrong. No application should write to Program Files.
See also Application does not work when installed with Inno Setup.
I'm very new to Inno Setup, so forgive my ignorance on this one.
I created a very small install script and it's building and working the way I want—I get my setup.exe built to the output directory, and all the source files are being copied to my specified destinations.
Now I want to make sure users can uninstall the files that I specified in my [Files] section of my script. The problem is I don't understand how Inno Setup handles this. I assume Inno Setup doesn't make an executable specifically for Uninstall, but even if I run setup.exe after I have installed my application, the wizard doesn't ask if I want to uninstall.
However, if I enable the Run menu's Target Uninstall in the ISC compiler, I am able to uninstall the files. So my question is, how do I uninstall my application outside of the ISC compiler. In my [Setup] section I do have Uninstallable=yes.
I know this is a total noob question, but any help is appreciated.
(As you have found yourself), Inno Setup creates an entry in Add/Remove Programs Control Panel applet (if CreateUninstallRegKey is yes).
The entry is a link to an uninstaller program, which is generated by the compiler (when Uninstallable is yes).
The uninstaller program is located by default in the application directory (unless overridden by UninstallFilesDir) and is named unins001.exe (the number is incremented, if needed, to avoid naming conflicts).
I have an application that uses Inno Setup as its installer.
I am now writing an updater using Inno Setup to apply some updates to various installed locations.
This application can be installed on removable flash drives as a portable app and I would like to be able to roll out the updates across several drives/locations/directories for each drive attached to the PC at once.
Is there a way to get Inno Setup to roll out its contents as an update to each location in an array of locations?
Not directly. One option is to build an install for the files that is designed to be silent.
Then write a second install that compiles that uses the first one. Then you [Code] Section you could call ShellExecute() executing the first installer. You could call the first installer as many times as you wanted.
Although, I suspect this may really creates havok on the Add/Remove Programs.