I have recorded an audio.
I dont know how it happened that only one sided speech is recorded and the other speech is recorded with a very low sound.
Is there any solution to amplify the other side signal.
any help would be much appreciated.
This question is probably more appropriately asked at a forum where recording and mixing is discussed. For example: https://sound.stackexchange.com/
The ideal would be to improve your recording situation, to control factors so the sound are more closely matched. (Match microphones, isolate the speakers from environmental sounds, optimize input levels, etc.)
After that, the next option or step is to pre-process your audio files with a tool like Audacity. Use this or another DAW (Digital Audio Workstation) tool to match amplitudes or employ noise filtering or a range of other tools.
Audio processing is both tricky (an "art") and cpu intensive, so it's good to get as much of this handled as possible before the sounds are imported into a program.
Related
I work in the field of phonetics and often need to record human speech for acoustic analysis. I have two questions that I couldn't find answers:
If I record in stereo channels, I need to convert to mono later on to proceed with annotation. So in principle mono signal is good enough. Are there reasons that stereo sound should be used (e.g. the signal would be better?)
Also, we were warned that the gain level should be kept small so that the recording level shouldn't exceed the maximum, which leads to signal cuttoff. However, I was also criticised when the recording file shows too low an amplitude (it's still very clear though), for that leads to a low SNR. How do people choose an appropriate gain level?
As the act of recording is involved, the Sound Design forum might be your best bet.
I can't think anything that might be gained, in terms of frequency analysis, by having a stereo signal. Stereo is more about locating the source of a sound in 3D space. Does the source of sound emit different frequency profiles in different directions? Does the environment filter the sound differently over the course of the two paths to the stereo inputs? If the the answer is "not significantly" then mono should be fine.
Choosing an appropriate gain level is mostly a matter of knowing your equipment. Ideally, your recording setup will provide feedback (usually a visual meter of some sort) that shows the signal strength. The "best" would be (theoretically) the loudest level that does not distort. So you have to know at what level distortion happens on all the elements of the recording chain.
There can be some fudging on this, given that the loudest peak on a recorded segment may be an outlier.
I'm currently researching an problem regarding DOA (direction of arrival) regression for an audio source, and need to generate training data in the form of audio signals of moving sound sources. In particular, I have the stationary sound files, and I need to simulate a source and microphone(s) with the distances between them changing to reflect movement.
Is there any software online that could potentially do the trick? I've looked into pyroomacoustics and VA as well as other potential libraries, but none of them seem to deal with moving audio sources, due to the difficulties in simulating the doppler effect.
If I were to write up my own simulation code for dealing with this, how difficult would it be? My use case would be an audio source and a microphone in some 2D landscape, both moving with their own velocities, where I would want to collect the recording from the microphone as an audio file.
Some speculation here on my part, as I have only dabbled with writing some aspects of what you are asking about and am not experienced with any particular libraries. Likelihood is good that something exists and will turn up.
That said, I wonder if it would be possible to use either the Unreal or Unity game engine. Both, as far as I can remember, grant the ability to load your own cues and support 3D including Doppler.
As far as writing your own, a lot depends on what you already know. With a single-point mike (as opposed to stereo) the pitch shifting involved is not that hard. There is a technique that involves stepping through the audio file's DSP data using linear interpolation for steps that lie in between the data points, which is considered to have sufficient fidelity for most purposes. Lot's of trig, too, to track the changes in velocity.
If we are dealing with stereo, though, it does get more complicated, depending on how far you want to go with it. The head masks high frequencies, so real time filtering would be needed. Also it would be good to implement delay to match the different arrival times at each ear. And if you start talking about pinnas, I'm way out of my league.
As of now it seems like Pyroomacoustics does not support moving sound sources. However, do check a possible workaround suggested by the developers here in Issue #105 - where the idea of using a time-varying convolution on a dense microphone array is suggested.
I have a situation where I have a video capture of HD content via HDMI with audio from a sound board that goes through a impedance drop into a microphone input of a camcorder. That same signal is split at line level to a 'line in' jack on the same computer that is capturing the HDMI. Alternatively I can capture the audio via USB from the soundboard which is probably the best plan, but carries with it the same issue.
The point is that the line in or usb capture will be much higher quality than the one on HDMI because the line out -> impedance change -> mic in path generates inferior quality in that simply brushing the mic jack on the camera while trying to change the zoom (close proximity) can cause noise on the recording.
So I can do this today:
Take the good sound and the camera captured sound and load each into
audacity and pretty quickly use the timeshift toot to perfectly fit
the good audio to the questionable audio from the HDMI capture and
cut the good audio to the exact size of the video. Then I can use
ffmpeg or other video editing software to replace the questionable
audio with the better audio.
But while somewhat quick and easy, it always carries with it a bit of human error and time. I'd like to automate this if possible as this process is repeated at least weekly throughout the year.
Does anyone have a suggestion if any of these ideas have merit or could suggest another approach?
I suspect but have yet to confirm that the system timestamp of the start time may be recorded in both audio captured with something like Audacity, or the USB capture tool from the sound board as well as the HDMI mpeg-2 video. I tried ffprobe on a couple audacity captured .wav files but didn't see anything in the results about such a time code, but perhaps other audio formats or other probing tools may include this info. Can anyone advise if this is common with any particular capture tools or file formats?
if so, I think I could get best results by extracting this information and then using simple adelay and atrim filters in ffmpeg to sync reliably directly from the two sources in one ffmpeg call. This is all theoretical for me right now-- I've never tried either of these filters yet-- just trying to optimize against blind alleys by asking for advice up front.
If such timestamps are not embedded, possibly I can use the file system timestamp for the same idea expressed in 1a, but I suspect the file open of the two capture tools may have different inherant delays. Possibly these delays will be found to be nearly constant and the approach can work with a built-in constant anticipation delay but sounds messy and less reliable than idea 1. Still, I'd take it, if it turns out reasonably reliable
Are there any ffmpeg or general digital audio experts out there that know of particular filters that can be employed on the actual data to look for similarities like normalizing the peak amplitudes or normalizing the amplification of the two to some RMS value and then stepping through a short 10 second snippet of audio, moving one time stream .01s left against the other repeatedly and subtracting the two and looking for a minimum? Sounds like it could take a while, but if it could do this in less than a minute and be reliable, I suspect it could work. But I have only rudimentary knowledge of audio streams and perhaps what I suggest is just not plausible-- but since each stream starts with the same source I think there should be a chance. I am just way out of my depth as to how to go down this road, so if someone out there knows such magic or can throw me some names of filters and example calls, I can explore if I can make it work.
any hardware level suggestions to take a line level output down to a mic level input and not have the problems I am seeing using a simple in-line impedance drop module, so that I can simply rely on the audio from the HDMI?
Thanks in advance for any pointers or suggestinons!
I'm trying to make a video tutorial, so i decided to record the speeches using a TTS online service.
I use Audacity to capture the sound, and the sound was clear !
After dinning, i wanted to finish the last speeches, but the sound wasn't the same anymore, there is a background noise(parasite) which is disturbing, i removed it with Audacity, but despite this, the voice isn't the same ...
You can see here the difference between the soundtrack of the same speech before and after the occurrence of the problem.
The codec used by the stereo mix peripheral is "IDT High Definition Codec".
Thank you.
Perhaps some cable or plug got loose? Do check for this!
If you are using really cheap gear (built-in soundcard and the likes) it might very well also be a problem of electrical interference, anything from ...
Switching on some device emitting a electro magnetic field (e.g. another monitor close by)
Repositioning electrical devices on your desk
Changes in CPU load on your computer (yes i'm serious!)
... could very well cause some kinds of noises with low-fi sound hardware.
Generally, if you need help on audio sounding wrong make sure that you provide a way to LISTEN to the files, not just a visual representation.
Also in your posted waveform graphics i can see that the latter signal is more compressed, which may point to some kind of automated levelling going on somewhere in the audio chain.
I'm trying to compare sound clips based on microphone recording. Simply put I play an MP3 file while recording from the speakers, then attempt to match the two files. I have the algorithms in place that works, but I'm seeing a slight difference I'd like to sort out to get better accuracy.
The microphone seem to favor some frequencies (add amplitude), and be slightly off on others (peaks are wider on the mic).
I'm wondering what the cause of this difference is, and how to compensate for it.
Background:
Because of speed issues in how I'm doing comparison I select certain frequencies with certain characteristics. The problem is that a high percentage of these (depending on how many I choose) don't match between MP3 and mic.
It's called the response characteristic of the microphone. Unfortunately, you can't easily get around it without buying a different, presumably more expensive, microphone.
If you can measure the actual microphone frequency response by some method (which generally requires having some etalon acoustic system and an anechoic chamber), you can compensate for it by applying an equaliser tuned to exactly inverse characteristic, like discussed here. But in practice, as Kilian says, it's much simpler to get a more precise microphone. I'd recommend a condenser or an electrostatic one.