May i ask if it's possible to capture Bluetooth traffic to and from the computer (MacOS, Windows or linux)?
Since i am trying to use wireshark to capture traffic but having no sign for success of capturing the bluetooth traffic.
It is possible without adapters on Linux, but requires additional configuration with bluez (and the necessary bluetooth hardware).
There are also commercial peripherals available from multiple vendors that may support your OS.
Related
I have a USB audio device (Scarlett Focusrite 18i6) which does not require a driver, so I assume it uses the USB HID Audio Class standard.
It works on everything from Windows and Mac to Linux and iOS.
But on Mac and Windows, it has a control application which can for instance enable and disable direct monitoring.
How would I go about reverse-engineering how this is done, so that I can reproduce it on platforms where the control application does not exist?
I'm thinking of booting up Windows in a VMWare session and then logging the USB communication (somehow?) while using the control application, but it does sound tedious considering the amount of data and my very limited understanding of USB.
Any other suggestions?
You could try running the control application using Wine instead of reverse engineering it. However, if it's accessing USB devices then there is a good chance it might be using an API not supported by Wine.
To reverse engineer it, you should find a way to look at the USB traffic between the computer and the device. Total Phase has some hardware USB protocol analyzers, but you might be able to find a good software solution for free.
I am on debian and:
I have a USB controller hooked up to a USB port on my PC (Device 1).
I have a male to male USB cord hooked up to another port on the PC that connects to Device 2. (it is a "bridging" usb cord, and has the chip for it)
I want to make them connect to each other as if they were one cord, so neither device knows that there is a computer in the middle.
This would be called a 'Coupler', except that I am using a PC as a coupler.
Here is a (really bad) diagram I made:
What I have done:
I have been able to connect the two devices independently of each other and sniff the results for when they fail to connect. The devices don't send a large volume of data back and forth.
Maybe there is some kind of command tool that I could use, for example (psudocode):
$ couple-usb-ports PORT1 PORT2
You're trying to reinvent the wheel here.
You might consider looking at this link instead.
http://dan3lmi.blogspot.com/2012/10/sniffing-usb-traffic-different.html
Specifically this.
Windows: You cannot directly capture raw USB traffic on Windows with Wireshark/WinPcap, but it is possible to capture and debug USB traffic on a virtual Windows machine under Oracle Virtual Box.
You cannot use a simple PC as transparent USB sniffer without extra (expensive) hardware. An USB bus has always one host (and one or more devices), and the PC can only be the host. This is a hardware limitation.
But you can capture USB data in a Windows machine using Wireshark and USBPcap, eliminating the need for the middle box in most cases.
As this post is tagged Linux, I suppose the controller PC is a Linux machine. Instead of connecting USB ports with a male-male connector, which is all kinds of bad (you are connecting the 5V lines of both machine with each other!), just run Wireshark in the controller PC.
There might be a little work to be done previously, as you have to enable Wireshark for USB monitoring (Particularly in Debian, this is disabled by default), and you might have to install a small driver to enable the monitoring. Have a look at this page for more information.
Once you get it working, Wireshark is an excellent tool for this!
I'd like to redirect traffic from and to USB devices in an application.
Particularly I want to talk to USB dongles.
So for example if a dongle is connected on a USB port, is it possible to get the traffic that is intended to be written to this device? On the other hand, can you simply write data in the same manner?
I don't have any experience so I'd appreciate to get some directions.
BTW, this is not intended to be used in anything illegal ;-)
With "USB dongles" you mean: Software license dongles?
First of all you should know that USB is not a stream of data such as RS232 but a very complex bus transferring a lot of different control and data messages.
On Linux you can use Wireshark to monitor the data on the USB bus. There are similar tools for Windows (up to Windows XP only) but the Windows version of Wireshark does only support Ethernet and not USB. Windows 7 has a built-in command line tool that does the same job.
If you really want to redirect data you might use something like "usbip" that allows sharing USB ports over network. You may simulate an USB dongle device by programming a server that simulates the dongle... However doing this is very tricky and requires a lot of programming experience!
For my project I have an Android phone and an Arduino device that communicate via Bluetooth. I was wondering if anyone knows any software tools I could use to monitor a bluetooth communications between two devices. Something like a packet eavesdropping. Preferably for Linux.
Take a look at ubertooth one. In the linked webpage there are instructions on how to build the dongle, as well as links to shops selling assembled dongles may be bought. Ubertooth one should work well with Kismet, and thus in Linux, by using a BT plugin (disclaimer: I have no personal experience on this).
Sounds like you are after a Bluetooth sniffer.
Bad news: They are almost exclusively Windows OS based and cost mega-$.
http://www.fte.com/products/bluetooth.aspx
If you were using BlueZ for one side of the communication you could use the BlueZ HCIDUMP app and Wireshark.
I don't think anyone has made a Linuz/Bluez Sniffer - could be wrong.
Can a WindowsCE device connect so more than one BlueTooth device? The device needs to both serve as a BlueTooth hands-free speaker for a phone and connect to a third device via a serial BlueTooth connection.
Can an application do this without the need of a speciel driver?
You must understand that Windows CE is a modular OS and any specific platform capabilities are implemented by an OEM. An OEM can create a Windows CE device with absolutely no Bluetooth support or they might choose to implement just a Bluetooth client profile (say as a bluetooth audio device) or they may choose to implement a Bluetooth server so they can consume a Bluetooth serial device. They may also choose to implement both. Beyond what the OEM does in software, the hardware itself might allow only one or the other (or both or neither for that matter).
The short of this is that we can't actually answer your question becasue there is no generic answer that fits all devices. You have to ask the Device OEM what they support and if they can extend that support if they don't support what you need.