We are trying to make an USB HID enumeration to simulate a keyboard device on a BLED 112 (with MCU C8051): http://www.silabs.com/products/wireless/bluetooth/bluetooth-low-energy-modules/ble121lr-bluetooth-smart-long-range-module1
We read in the BLUETOOTH SMART MODULE (last version : 12/20/2016) that : "There is no support in the current BLE stack for other types of USB enumeration such as USB HID or other protocols".
But we found examples to make HID keyboard, but only in one way : computer to usb dongle.
So we would like to know if it is possible to make an HID usb enumeration where the dongle send keyboard event to the computer.
If someone have clues, example, or other, it will be great
thanks for your help.
just for information, this is the response given by the silicon labs technical team :
"Unfortunately that is not possible, the BLED112 enumerates as a USB CDC device only. It communicates with the PC using BGAPI messages which is our proprietary protocol to interface with our modules."
Related
I am learning to program a USB device (iBall 3.5g USB Dongle) using libusb.h header library.
Until now I am able to identify my device using the Vendor ID and also open the device for operation.
As a next step I would like to know the available commands (or the controls) for example : command to scan the surroundings for available GSM networks.
Obviously I will have to talk to the devices' firmware to extract the necessary information.
I tried to search for the technical datasheet for the 3g dongle, but couldn't find any.
The dongle is powered by a Qualcomm chip
Do you know any of the methods in which I can get the control commands for a usb device ?
Thanks in advance.
There is no simple procedure for figuring out what commands a USB device has. You need to use a combination of looking at the descriptors reported by the device, seeing if the device supports any particular USB device class, reading the USB specification, and maybe doing some reverse engineering using a protocol analyzer.
A good first step would be for you to use lsusb -v to print human-readable descriptions of the device's USB descriptors.
I have a USB HID device which acts as a normal USB HID keyboard. In addition it implements some additional commands (USB HID display).
Is there any way I can write a driver/application to control the display part while leaving the keyboard part up to the kernel/built-in HID drivers?
I already tried to claim the endpoint using libusb. That did not work out as the internal generic USB HID driver already did that.
You can use a HID library like libhid to connect to the USB HID driver instead of trying to take over it.
I have been asked to figure out how to achieve bluetooth communication through an off-the-shelf dongle (in this case a dongle utilizing the Broadcom BCM2045 chip) using the FTDI Vinculum 2 (VNC2) USB controller. I have custom firmware written for the VNC2 to communicate with a generic USB device with the VNC2 acting as the host, and I can successfully read the VID and PID from the dongle as well as the USB device class, subclass, and protocol. I can also send data to the dongle using the bulk data endpoint and I believe the device is receiving though I have no way to tell at the moment.
So I believe I can communicate with the dongle, the problem is I have no idea WHAT to communicate to it in order to set it up in discoverable mode or to pair it with another discoverable device, nor how to actually transmit data through the wireless link once it is paired. I don't even know if there exists a standard communication protocol for this type of thing or if every device will be different. I have a vague understanding of the bluetooth protocol stack and it is my understanding that I won't be required to fully understand that as it should be implemented in the dongle on one end and in the android smartphone that we hope to connect to on the other end. Like I said, I can currently send data to the bulk endpoint, is it true that this endpoint is only for data transfer over the wireless link and I will need to connect to a different endpoint in order to send setup/configuration messages to the dongle?
In short, I need to know what data to send over the USB bus to control any generic bluetooth dongle if possible or at least one specific bluetooth dongle. I have a USB port sniffer but the complexity of the output while using the dongle to communicate is staggering and I doubt I'll ever figure it out.
Thank you in advance.
Bluetooth dongles communicate with host software stack using HCI (host control interface), which is defined in the Bluetooth spec. For reference, you can look at source code for the open source BlueZ stack (standard linux stack). You could run BlueZ on linux talking to your USB dongle, and use hcidump to capture actual packets going across HCI. You can also check out hcitool and hciconfig for performing specific actions.
I bought one of those tiny bluetooth USB dongles that you can plug on a PC and make bluetooth communications. I am wondering if I just plug this dongle to a USB power source, like the USB charger that comes with iPad, can the bluetooth dongle power up, and be discovered as a bluetooth device? This sounds reasonable, since the bluetooth dongle should be able to broadcast itself, at least using some low-level protocol, i.e. showing its Mac address.
However, I tried to do the following:
1.Plug the bluetooth dongle on my iPad's usb charger
2.Search bluetooth devices on my laptop
and I could not find it. Is it because the bluetooth dongle needs the PC to initialize it, so that it can be discovered? Or I am not doing it right?
Thanks
It depend on the dongle
Typical PC dongles depends on the host (pc) to initialize and start any bluetooth activity - including scanning etc
It is practically possible to make dongles that can start becoming discoverable without waiting for host initialization. This has to be a custom build
I have a Linux virtual machine running on VMWare Fusion (on Mac OS X) that I intend to use as a development environment for an embedded system. Would it be possible for my Linux VM to talk to my embedded system's serial port using a USB-to-serial adapter? Any recommendations for what sort of adapter I should get?
There are two ways to do it:
Your host-OS supports your USB<->serial converter (very likely). If so you can just allow your VM to talk to the serial port. If so the VM will see a standard serial port and everything will be fine.
Your guest-os in the VM supports the USB<->serial converter, AND your host-OS allows raw USB forwarding.
All in all the chances are good that it works..
Btw: there are good and bad USB<->Serial converters. If you find out that the serial connection seems to work (everything detects/works as expected for a couple of seconds), but you can't get a reliable connection for a longer time, then it's very possible that the usb<->serial dongle sucks....
You get what you pay for... When buying these things I'd check comp.arch.embedded and ask which usb dongles are known to just work, and which not. (My recommendation is to stick with products from Assmann. You can order them at digikey).
I've found USB serial adaptors to be a bit hit & miss with embedded work. One thing to be aware of is that the buffering tends to work differently from "real" serial ports, and latency of characters through the system can be quite variable. Some embedded development systems (think bootloaders, cheap JTAG probes etc) can be quite sensitive to this and will give timeouts and so on.
Note this doesn't only apply to USB serial adaptors, I've had similar problems with high end multi-port serial cards, but usually with those you can tweak the FIFO / IRQ settings to get something working.
I have experienced that a USB to serial adapter with a FTDI chipset and drivers is more reliable and compatible with more devices than the Prolific chipset
Depends upon the VM software, but VMWare Fusion does support USB devices. The question becomes, does your IDE support talking to a USB device instead of an old-fashioned serial port? With Linux, probably yes.
I had no problems whit serial adapters from ATEN.
USB serial adapter is USB standard device (just like mass storage) that mean that any USB compliant adapter should work.
pl2303: I have found this device to be very reliable and are often in the generic and cheap USB to RS232 adapters. I've seen expensive adapters fail and my generic adapter from geeks.com work great.
I just picked up a USB 1.1 - RS232 adapter (Digitus DA-70119) from WeirdStuff for 10 bucks. I plugged it into my Mac mini and VMWare Fusion showed me this.
Once I clicked on the USB icon, my Ubuntu 9.10 VM had no trouble seeing it
$ lsusb
Bus 002 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
$ dmesg
usb 2-1: new full speed USB device using uhci_hcd and address 4
usb 2-1: configuration #1 chosen from 1 choice
pl2303 2-1:1.0: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB0
I can now use /dev/ttyUSB0 in my Linux VM to talk to my target system.