I tried to connected Android Auto DHU r1.1 in windows with the Android Emulator in Android Studio，but got this error.
In emulator:
Communication error 8.
In desktop head unit:
Shutting down connection due to authentication failure.
I have checked the time, time zone and got the newest android auto.
adb forward tcp:5277 tcp:5277 (set adb proper port)
Stop head unit -> Start head unit (on the phone)
Launch desktop-head-unit.exe
and read https://developer.android.com/training/cars/testing#running-dhu
Work fine for me
Today I got a problem .There is neither usb device nor virtual device in the dialog.
But I can find device with commond.
Maybe there is something wrong with Android Studio.
How can I fix the problem?
After a day,I found the problem. The error is
WARN - #com.android.ddmlib - Unable to open connection to: localhost/30.129.144.64:5037, due to: java.net.ConnectException: Operation timed out
So I add localhot 127.0.0.1 to host file，and then restart AS.Everything is OK
I installed the current lirc package (0.9.0~pre1-1.2) on a Raspian jessie (no pixel) (everything updated and upgraded) and connected to the (lirc default) GPIO ports:
to gpio port 17 - an IR LED via transistor etc
to gpio port 18 - an IR receiver nodule
The receiver part works perfectly:
mode2 command receiving raw data from transmitter
the IR code recognition of previously recorded keys works
However, the IR LED only works only while lirc is not involved:
a shell script can switch the IR LED on and off with no problem
The only thing that doesn't work:
irsend does not make the IR transmitter emit anything, however no error message is shown
So the hardware, especially the IR LED is definitely working, while lirc cannot make the LED emit any configured IR code.
Please note that this seems to be a duplicate of
stackoverflow: irsend is not giving errors, but does not send signal on Raspbian
Unfortunately it is not. The "solution" provided there was placing the data for /etc/modules into the file /etc/modules-load.d/lirc_rpi.conf. I tried that as well, but it makes no difference.
Any help is greatly appreciated!
Configuration data follows - if any other data is required, I'd be happy to add it! TIA!
System and lirc Configuration
Extract fom: /boot/config.txt
dtoverlay=lirc-rpi,gpio_in_pin=18,gpio_out_pin=17,debug=on
Extract of: /etc/modules
lirc_dev
lirc_rpi gpio_in_pin=18 gpio_out_pin=17
(not sure if that is necessary at all, does not make a difference if this is not configured!? Any hint apppreciated)
All active entries in: /etc/lirc/hardware.conf
LIRCD_ARGS="--uinput"
DRIVER="default"
DEVICE="/dev/lirc0"
MODULES="lirc_rpi"
LIRCD_CONF=""
LIRCMD_CONF=""
Some system output
1) The driver is loaded, output of following command right after boot, output of: dmesg | grep lirc
lirc_dev: IR Remote Control driver registered, major 245
lirc_rpi: module is from the staging directory, the quality is unknown, you have been warned.
lirc_rpi: to_irq 178
lirc_rpi: auto-detected active low receiver on GPIO pin 18
lirc_rpi lirc_rpi: lirc_dev: driver lirc_rpi registered at minor = 0
lirc_rpi: driver registered!
input: lircd as /devices/virtual/input/input0
lirc_rpi: Interrupt 178 obtained
2) the service is started and running, output of: systemctl status lirc
? lirc.service - LSB: Starts LIRC daemon.
Loaded: loaded (/etc/init.d/lirc)
Active: active (running) since Mo 2017-06-12 20:04:03 CEST; 2h 58min ago
Process: 377 ExecStart=/etc/init.d/lirc start (code=exited, status=0/SUCCESS)
CGroup: /system.slice/lirc.service
+-437 /usr/sbin/lircd --driver=default --device=/dev/lirc0 --uinput
3) the modules are loaded, output of: lsmod | grep Module;lsmod | grep lirc
Module Size Used by
lirc_rpi 8453 3
lirc_dev 10211 1 lirc_rpi
rc_core 23776 1 lirc_dev
I followed the troubleshooting steps in the (outdated) manual at http://aron.ws/projects/lirc_rpi/
to get some more information.
Output of: cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-53, parent: platform/20200000.gpio, pinctrl-bcm2835:
gpio-35 ( |? ) in hi
gpio-47 ( |? ) out lo
I have seen that output also in this case:
raspberrypi.stcakexchange: LIRC won't transmit (irsend: hardware does not support sending)
This user is as irritated by that output as I am - can somebody please tell why gpio-35 and gpio-47 are listed here? shouldn't it be gpio-17 and gpio-18?
Output of: cat /proc/interrupts | grep lirc
178: 875 pinctrl-bcm2835 18 Edge lirc_rpi
This matches the dmesg output on having obtained interrupt 178
Any other dmesg output of lircd, no matter what action, is repeatedly (most likely due to the debug option set) only
lirc_rpi: SET_SEND_CARRIER
lirc_rpi: in init_timing_params, freq=38000 pulse=13157, space=13158
lirc_rpi: SET_SEND_DUTY_CYCLE
lirc_rpi: in init_timing_params, freq=38000 pulse=13157, space=13158
Having restarted testing again after some time for to build up a test copy of the circuit, the problem occurred again. And now, after some more month of much testing, having asked lots of people for help (no one could help), even having purchased and built up a cheap mini USB oscilloscope kit for to examine the hardware further, I finally found the solution.
Long story short: everything in the configuration was correct, and all of the attached hardware was fine. The problem was the testing script - see my remark on
"a shell script can switch the IR LED on and off with no problem"
and as I did not put it in the above description, nobody could have found the solution myself....
The script uses the pseudo files in /sys/class/gpio, see an example here:
raspberry-projects.com: IO pin control from the command line
At the end of the script a command writes to /sys/class/gpio/unexport for cleanup purposes, and this step seems to reset a GPIO port to always end up in the state of being configured for input. As a result LIRC is not longer able to control this GPIO port, since it seems to configure the GPIO port for output only during system boot, and after that always expecting the port to be in that state.
I tracked the problem down to this point by using the gpio utility from the wirinpi package (install with sudo apt-get wiringpi), executing gpio readall and checking for differences.
The time when everything suddenly worked again, I simply may have fogotten about to run my testscript before testing LIRC, which I otherwise always did...
Luckily the problem with the port configuration can easily be fixed without having to reboot the system. Again I use the gpio utility to reset reset the used port for output, where in the below example
the default output port 17 for LIRC is used and
the parameter -g lets the utility use the ordinary GPIO port numbering and not that very different one of the wiringpi package and library
Here is the command, after having executed this last in my test script, LIRC can properly send IR codes again:
gpio -g mode 17 out
I am using Mac OSX El Captain with Android Studio 2.2.
Android Studio start to don't show Android devices suddenly. I try to kill adb server and start it again and this errors appear on terminal.
List of devices attached
daemon not running. starting it now on port 5037 *
adb E 1165 84563 usb_osx.cpp:307] Could not clear pipe stall both ends: e0004051
adb E 1165 84563 usb_osx.cpp:289] Could not find device interface
daemon started successfully *
When I try to kill server twice for understanding the issue it gives this error message:
error: protocol fault (couldn't read status): Connection reset by peer
Try restarting your Mac and devices. I ran into a similar error and restart got rid of it :)
I am trying to implement a virtual mouse driver according to the Essential Linux device Drivers book. There is a user space application, which generates coordinates as well as a kernel module.
See: Virtual mouse driver and userspace application code and also a step by step on how to use this driver.
1.) I compile the code of the user space application and driver.
2.) Next i checked dmesg output and have,
input: Unspecified device as /class/input/input32
Virtual Mouse Driver Initialized
3.) The sysfs node was created properly during initialization (found in /sys/devices/platform/vms/coordinates)
4.) I know that the virtual mouse driver (input32 ) is linked to event5 by checking the following:
$ cat /proc/bus/input/devices
I: Bus=0000 Vendor=0000 Product=0000 Version=0000
N: Name=""
P: Phys=
S: Sysfs=/devices/virtual/input/input32
U: Uniq=
H: Handlers=event5
B: EV=5
B: REL=3
5.) Next i attach a GPM server to the event interface: gpm -m /dev/input/event5 -t evdev
6.) Run the user space application to generate random coordinates for virtual mouse and observe generated coordinates using od -x /dev/input/event5.
And nothing happens. Why?
Also here author mentioned that gdm should be stopped, using /etc/init.d/gdm stop, but i get "no such service" when stopping gdm.
Here is my complete script for building and runing virtual mouse:
make -C /usr/src/kernel/2.6.35.6-45.fc14.i686/ SUBDIRS=$PWD modules
gcc -o app_userspace app_userspace.c
insmod app.ko
gpm -m /dev/input-event5 -t evdev
./app_userspace
Makefile:
obj-m+=app.o
Kernel version: 2.6.35.6
As i said before i can recieve the result through od, but i received it through your program
echo 9 19 > /sys/devices/platform/virmouse/vmevent
gives:
time 1368284298.207654 type 2 code 0 value 9
time 1368284298.207657 type 2 code 1 value 19
time 1368284298.207662 type 0 code 0 value 0
So now the question is: what is wrong with X11? I would like to stress, that i tried this code under two different distributions Ubuntu 11.04 and Fedora 14.
Maybe this will help: in Xorg.0.log i see the following:
[ 21.022] (II) No input driver/identifier specified (ignoring)
[ 272.987] (II) config/udev: Adding input device (/dev/input/event5)
[ 272.987] (II) No input driver/identifier specified (ignoring)
[ 666.521] (II) config/udev: Adding input device (/dev/input/event5)
[ 666.521] (II) No input driver/identifier specified (ignoring)
I spent a huge amount of time, resolving this issue, and i would like to help other people, who run in this problem. I think some outer X11 features interfered my module work. After disabling GDM it now works fine (runlevel 3). Working code you can find here http://fred-zone.blogspot.ru/2010/01/mouse-linux-kernel-driver.html working distro ubuntu 11.04 (gdm disabled)
Try replacing the below lines of code in the input device driver
set_bit(EV_REL, vms_input_dev->evbit);
set_bit(REL_X, vms_input_dev->relbit);
set_bit(REL_Y, vms_input_dev->relbit);
with
vms_input_dev->name = "Virtual Mouse";
vms_input_dev->phys = "vmd/input0"; // "vmd" is the driver's name
vms_input_dev->id.bustype = BUS_VIRTUAL;
vms_input_dev->id.vendor = 0x0000;
vms_input_dev->id.product = 0x0000;
vms_input_dev->id.version = 0x0000;
vms_input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REL);
vms_input_dev->keybit[BIT_WORD(BTN_MOUSE)] = BIT_MASK(BTN_LEFT) | BIT_MASK(BTN_RIGHT) | BIT_MASK(BTN_MIDDLE);
vms_input_dev->relbit[0] = BIT_MASK(REL_X) | BIT_MASK(REL_Y);
vms_input_dev->keybit[BIT_WORD(BTN_MOUSE)] |= BIT_MASK(BTN_SIDE) | BIT_MASK(BTN_EXTRA);
vms_input_dev->relbit[0] |= BIT_MASK(REL_WHEEL);
It worked for me on ubuntu 12.04