I am using IIS 7.5 on Windows Server 2008 R2.
From this server, I can access the localhost (standard IIS start page is displayed).
But I can't access it from any other machine belonging to the same network.
I have the impression that the problem is that my server is not listening at the address 0.0.0.0:80.
Because when I do a netstat -aon | findstr 80 I get only:
TCP 127.0.0.1:80 0.0.0.0:0 LISTENING 4
TCP [::]:80 [::]:0 LISTENING 4
But if I do netsh http show iplisten I then see (I have added the two last ones manually)
IP addresses present in the IP listen list:
-------------------------------------------
127.0.0.1
0.0.0.0
::
One additional test that I did:
When I try netcat -v xx.xxx.xx.xx 80 on the client, I get the error "Connection refused".
But after doing netcat -l -p 80 on the server, the netcat connection from client works and I can exchange data.
Because of this I don't think that it is a firewall issue.
Do you have any idea on the causes and how to solve the issue?
Thanks a lot in advance for your feedback!
Related
I set my linux as an access point, and then run simple web-server that print "hello world" at port 3000.
and connect it with my smart phone successfully.
in linux terminal, http://localhost:3000 works well.
But in smart phone,
If I access to http://172.24.1.105:3000, can't connect to it. (172.24... is ap's ip)
the chrome's error message is
This site can't be reached. 172.24.1.105 refused to connect
I searched Google (https://serverfault.com/questions/725262/what-causes-the-connection-refused-message) and I suspicious linux's firewall.
pi#raspberrypi:~/prj/ap_server $ sudo tcpdump -n icmp
listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
... when I access to port 3000,
15:07:13.102750 IP 192.168.0.3 > 168.126.63.2: ICMP 192.168.0.3 udp port 42531 unreachable, length 386
the log is above. so I couldn't reach ap's webserver.
so I wonder two things...
1. How can I disable to its port block?
2. in tcpdump log, I access to port 3000 actually, why the log print port 42531?
Plus)
even I type sudo service iptables stop, the problem is not solved
sudo netstat -ntlp | grep 3000 logs:
**tcp6 0 0 :::3000 :::* LISTEN 1999/nodejs**
+I followed this tutorial-> https://frillip.com/using-your-raspberry-pi-3-as-a-wifi-access-point-with-hostapd/ .
and there is ipv4 setting.
If you want to run it on your mobile it will work on Live IP (externel) address
if it is working fine on local address (localhost) and not on live IP then
enable routing from your router
and allow that specific port it will work fine.
I found the issue.
my dhcp set was
interface=wlan0 # Use interface wlan0
listen-address=172.24.1.1 # Explicitly specify the address to listen on
bind-interfaces # Bind to the interface to make sure we aren't sending things elsewhere
server=8.8.8.8 # Forward DNS requests to Google DNS
domain-needed # Don't forward short names
bogus-priv # Never forward addresses in the non-routed address spaces.
dhcp-range=172.24.1.50,172.24.1.150,12h # Assign IP addresses between 172.24.1.50 and 172.24.1.150 with a 12 hour lease time
like above.
I tried to connect the external ip(172.24.1.105) that I can see on mobile continuously but got failed. but when I tried with 172.24.1.1, then success.
I don't know why. maybe there is accurate ip address and something in mobile is temporal.
See similar topic at Node JS not listening to port 1337 on server
Your web server is not listening remote address.
I have my meteor app running on my production server. I have a reverse proxy setup on a different server.
A curl from my reverse proxy server to my app server gives me a Connection Refused.
My app is running on port 8080 and my firewall allows access to the port. I suspect the reason for the connection refused is that my app is running on 127.0.0.1 instead of 0.0.0.0
On running sudo netstat -tapn I get a
tcp 0 0 127.0.0.1:8080 0.0.0.0:* LISTEN 14391/node
How do I get the app to run on 0.0.0.0. If this is not the reason, what else could cause a connection refused?
127.0.0.1 is the loopback IP it's usually the same as localhost (as defined in your hosts file). you should never be able to connect to that IP from the outside. 0.0.0.0 binds to all IPs on the server, which is accessible from the outside.
I have website working fine on my local machine as host name hml.frontend in the hosts file: 127.0.0.1 hml.frontend
In IIS I have bindings as hml.frontend 127.0.0.1 and hml.frontend 192.168.1.94. The latter I used ipconfig to get my local ip address issued to me by my BT Home Hub 5 router.
In windows 10 firewall I have allowed App/Feature NetLogon service and World Wide Web services (HTTP).
In advanced settings in Inbound Rules I have added a rule which allow the connection from all sources to ports 80 and 443. Scope is any IP addresses.
On my macbook I have added the 192.168.1.94 as hml.frontend to the hosts file.
I can ping hml.frontend OK from the macbook.
However from a web browser the http://hml.frontend site cannot be reached from the macbook.
telnet 192.168.1.94 80 from the macbook says unable to connect to remote host.
Back on the PC I have done netstat -na to see which ports IIS is listening on and 127.0.0.1:80 is there and so is 192.168.1.94:139 and many more ports against that IP address but not port 80.
Any ideas what I can check to get my PC to listen for that website hostname on port 80?
I got it to work, I was on the right track that the IP address was not being listened to.
In order to add the ip address I have to be listened to, I went into cmd as adminstrator, did
netsh
http
show iplisten
'show' result shows that just 127.0.0.1 was being listened on port 80
add iplisten ipaddress=192.168.1.94
show iplisten
quit
'show' result shows that now additionally 192.168.1.94 is being listened on port 80
Then I went back in with
netstat -na
And now I see the line I want:
TCP 192.168.1.94:80 0.0.0.0:0 LISTENING
Some information was gained from this article.
http://windowsitpro.com/windows-server/solve-iis-listener-problems
The site is now reachable from my macbook using the hostname http://hml.frontend
My laptop is running a local neo4j server. I can use it with localhost:7474 but when i try connecting it with 192.168.1.12:7474 it is unreacheable.
Turns out linux is blocking connections other than web server port 80. Because i can access my Apache server on 192.168.1.12/
I am trying to allow TCP connections on port 7474 by using
iptables -A TCP -p tcp --dport 7474 -j ACCEPT
but it gives a response as -
iptables: No chain/target/match by that name.
How can i make other clients access neo4j server running at my laptop on port 7474. My laptop IP addr is 192.168.1.12.
I doubt that it is blocking it. Probably your neo4j server is only running at 127.0.0.1. You can check this out with netstat -nplt: you will probably see something (the apache) listening on 0.0.0.0:80 or :::80 (e.g. catchall address) but on port 7474 you will probably only see 127.0.0.1:7474 or ::1:7474. If this is the case you need to reconfigure your neo4j server to listen not only on localhost (don't know how, checkout the documentation).
Okay. I had uncommented the webserver address line but it still wasn't working.
So i reinstalled neo4j. That solved it. Weird but worked.
Sorry in advance for such a noob question, but I'm certainly a noob.
My question is what does it mean to LISTEN or ACCEPT on a port as it relates to my example?
EXAMPLE:
I have a tomcat server, and It will use port 8080. I want to make sure that port is available for me to use.
What commands should I perform on my unix server and why?
what information would a command like this give me: netstat -an | grep LISTEN
If a port shows up as LISTEN in netstat, it means the port is in use by a server process, so you can't use it. Here is an example:
tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN
which shows that port 631 is in use.
Ignore the UNIX type sockets at the end - they are irrelevant.
For checking port 8080 is in use or not, you can simply use the command netstat -an|grep 8080. If you get an output in below format, that means 8080 is already in use and you need to assign a new port for the tomcat.
# netstat -an
tcp 0 0 127.0.0.1:8080 0.0.0.0:* LISTEN
Netstat command displays various network related information such as network connections, routing tables, interface statistics, masquerade connections, multicast memberships etc,
a option with netstat will give you both listening and non listening ports
n option when you don’t want the name of the host, port or user to be displayed, use netstat -n option. This will display in numbers, instead of resolving the host name, port name, user name. This also speeds up the output, as netstat is not performing any look-up.
For more understand the use of netstat command here are its options:
-a : All ports
-t : Ports TCP
-u : Ports UDP
-l : Listening ports
-n : IP address without domain name resolution
-p : Name of the program and it associated PID
So:
-To display all port (TCP & UDP), PId with the associated name of the program :
$ netstat -paunt
-To display all Listening ports (TCP), PId with the associated name of the program : (and we can also filter with the grep command)
$ sudo netstat -plnt | grep ':80'
I hope it will be helpful :)
You can also use telnet to check if the port is open and listening e.g,
Zeeshan$ telnet google.com 80
Trying 173.194.35.5...
Connected to google.com.
Escape character is '^]'.
I am telnetting google.com on port 80. If you see the third line in the output, you will notice it says it is connected with the Google's web server. The same way you have a JAVA application server called Tomcat and it is listening on port 8080. In fact it is asking clients to connect to it on port 8080 so it can give away the JAVA services to client. When I will use from a client side telnet localhost 8080 I will be connected the same way I have connected with Google's web server on port 80. Provided that Tomcat is running and listening on port 8080. If port 8080 is not free and occupied by some other application you can simply change the port 8080 to another free port. Telnet should give you the following status:
accepted (connected), refused, and timeout
connection refused - nothing is running on that port
accepted - some application is running on the port
timeout - a firewall is blocking access
So now there are two possible ways to check. From the same machine you are running Tomcat server:
telnet localhost 8080
Of if you want to check it from some other machine or outside of the network:
telnet 192.168.1.1 8080
I hope that helps.
use can also run the below command, it will list the Port and corresponding PID, if any process is using those ports
netstat -tulpn