I'm trying to create a combined scatter plot and "bar chart" - the bars extend the full height of the chart, but their width varies (I have a table with the start and finish points on the x-axis).
Here is a mock-up:
http://imgur.com/EHzv5YB
Do you think this is possible in Excel? I have found some links on how to overlay multiple plot types, but none involving variable width shaded areas as seen in the example.
Would really appreciate any help. Thanks!
I've written a tutorial showing how to Highlight Certain Time Periods in a Chart.
Related
I'm looking for a chart that allows me to have non-consistent axis to better capture outliers.
Something similar to below
The y-axis range varies quite a bit. I wanted a more elegant solution than what I did -- I superimposed two graphs, with the graph on top pulling its own range. I had to manually align the graphs so that they overlapped.
Thanks in advance!
I would like to create a bar-chart (or a histogram?) with vertical bars and a numerical x-axis , but I do not know how/where to start. I have MS-Excel and Origin-plot available with me. My intended chart would look like this:
You can more or less get what you want by adding and styling error bars appropriately to a scatter plot. The error bar is a simple way to force Excel to draw a line under/over the point.
Chart with data and error bars
Couple steps
Make an XY scatter chart
Add the error bars and delete the horizontal ones that come up
Set the negative error bar for the points to be equal to the same value that is being plotted
Set the positive error bar to 0 so it does not show
Change the formatting on the error bar to be thicker
Possible hide the initial dot shown so that it is bar only
You could take these steps and codify them with some VBA to prevent the tedious nature of doing this multiple times. Setting error bars is one of the worst activities to have to do continually.
I believe you should also be able to get your desired colors by adding multiple series. Possibly all the more reason to do this with VBA.
I have a combo chart in excel, with clustered bar charts (for a box plot) and lines. I am trying to display the bar charts/box plot in front of the lines, but am able to do so.
I tried moving the bar charts to the top and/or bottom in "select data" - but no change.
Any suggestions?
Am using Excel 2013.
Thanks!
I believe it is not possible. You can change display ordering of Excel series by:
changing the plot order of the series (this is what you have done in the "Select data" dialog),
changing the axis on which the series are displayed (series on secondary axis are displayed over the series on the primary axis).
But from my experiments no combination of changes makes the lines appear behind the columns.
There are two workarounds that might or might not help you:
you can create two charts on top of each other and put the chart with the lines behind the one with the columns,
or you could create a line chart (most likely you would need scatter chart), that is not a single line but a series of segments where the columns are not shown (this one is not that easy to do)
What are the lines for? If you are just trying to identify some zones along the value axis, you could instead use stacked areas, which would give a banded appearance. Areas are always drawn behind bars and columns, while lines are always drawn in front of lines and columns.
Do you know if this chart, as shown in the following image, can be done in Excel?
Chart:
I don't even know how this kind of chart is named, so I cannot search in the web for tutorials. I don't need to display three points on every row as in this chart (one is enough), and even I can mark the control group manually.
Yes this can be done in Excel.
If you want vertical orientation like on the picture above, then you should probably use the Scatter chart with quite some modifications. You would set the x values of the series to your values and the y values can be just 1,2,3,4,5.... The biggest problem with this approach would be how to display the correct categories. There is a tool to help you do that and it is discussed here: https://superuser.com/questions/485883/how-to-create-dynamic-scatter-plot-matrix-with-labels-and-categories-on-both-axi
For horizontal one you can use a normal line chart - with hidden line and only markers visible (Excel doesn't support vertical line graphs).
Even three groups are easy to do, you just need to add three series and format them accordingly.
The lines are also quite easy to do, you add minor / major gridlines to the chart and then format those as well.
Im using Excel for Mac 2011 and I have the following figure
I would like to still show the bubbles outside of the available chart area, while keeping the maximum and minimum axes values unchanged.
Create an identical chart with the same data, but with axis limits that show the full bubbles. Then set all the formatting in the chart other than the bubbles to the equivalent of "none", i.e, no axis labels, chart outlines, gridlines, chart and plot borders, background color, etc.
With very careful sizing and positioning of this bubbles-only chart over the original chart, you can get the bubbles to extend beyond the plot area of the original. If the size or position of a bubble is a little off, modify the overlay chart's data by the tiny amount needed to get the bubble to cover the underlying original bubble. Turn off the formatting for the underlying bubbles as last step.
NOT programmatic, very trial and error, and fussy, of course, and I hope someone comes up with a more elegant way to achieve your goal. But I was able to get it to work on my Windows machine.