Cannot access Puppet Learning VM - linux

Question

I have set up puppet learning VM on VirtualBox. I can ssh into it with:
ssh root#127.0.0.1 -p 2222
However, the guide says to do facter ipaddress, and ssh into the ipaddress that outputs. I get 10.0.2.15.
If I try that ipaddress, it does not work. I want to get it to work.
Also, I am supposed to be able to access the Puppet gui from https://10.0.2.15 and am not able to do that. I think the two problems are related.
I have 3 adapters set up. 1. NAT, 2. host only adapter, 3. bridged network.
For #1, I have port forwarding set up (am not able to ssh without it).
eth0 Link encap:Ethernet HWaddr 08:00:27:44:00:48
inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe44:48/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:15892 errors:0 dropped:0 overruns:0 frame:0
TX packets:24276 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1232127 (1.1 MiB) TX bytes:2062554 (1.9 MiB)
eth1 Link encap:Ethernet HWaddr 08:00:27:72:B7:0E
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
eth2 Link encap:Ethernet HWaddr 08:00:27:14:93:EE
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:322880 errors:0 dropped:0 overruns:0 frame:0
TX packets:322880 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:233893154 (223.0 MiB) TX bytes:233893154 (223.0 MiB)

Answer 1

NICs
I don't see any IP assigned to your NICs except eth0. I assume this learning VM is based on centos, please configure your network adapters correctly first.
check:
/etc/sysconfig/network-scripts/ifcfg-eth0
/etc/sysconfig/network-scripts/ifcfg-eth1
/etc/sysconfig/network-scripts/ifcfg-eth2
/etc/udev/rules.d/70-persistent-net.rules
This is no puppet or virtualbox issue.
port forwarding
Accessing https://10.0.2.15 will not work, this is an internal NAT network IP. Please create an entry for your VMs NAT Adapter under Port-Forwarding, just map Host Port 10443 to guest port 443. If you try to access https://localhost:10443 in your browser you should reach the service running on this VM and listening on port 443.(Check if the service is running and the firewall/iptables is open on all needed ports).

Answer 2

Patrick is right. The configuration within the CentOS box is strange.
It's working for me under windows but on my Ubuntu system I had big trouble setting up the Training VM.
My Tip: just add 22 and 80 port forwordings in your virtualbox.
Change -> Network -> Adapter 1 -> Port-Forwarding -> add
Protokol: TCP | Host-Port: 2222 | Guest-IP: 10.0.2.15 | Guest-Port: 22
-> you may connect now by:
ssh localhost -p 2222 -l root
also:
Protokol: TCP | Host-Port: 8081 | Guest-IP: 10.0.2.15 | Guest-Port: 80
-> you may access the questguide via:
http://localhost:8081