As part of installation, sometimes i see few erors during a file replacement etc, so then inno setup gives a message like "abort/retry/ignore" if the user chooses abort inno setup rollbacks the installation.
So i want to know 2 things here
1)I wanted to know from my installer, whether a roll back is invoked or not? can inno setup give any acknowledgeent for automatic rollback happend or not?
2)what are the steps of rollback, what all does it do in that? a detailed explanation would be very helpful...
Related
In Inno Setup, there is the AppMutex directive.
Using this directive, one can make Inno Setup stop / not start while this mutex exists.
I experience it sometimes that my users accidentally open my application while the setup (and update in this case) is still running.
This locks files, and Inno Setup can not replace them.
The solution in my opinion would be that Inno Setup creates a mutex and automatically closes it when it's finished.
When the user starts my app, the app would check if the mutex (which was created by Inno Setup) exists, and if it does, my app would close right away.
However, I do not find this as a built-in option in Inno Setup.
Do I have to code it manually, or am I missing something?
Thank you!
That's what SetupMutex directive does.
Or you can do it programmatically using CreateMutex function.
I am building an installer in Inno Setup v6.2.1 with prerequisites, which include .NET, runtimes, and KB fixes (Windows 7 SP1). The goal is to do potentially several reboots depending on if the machine is missing KBs or .NET etc.
I am able to achieve what I want so far using PrepareToInstall and can change the text by returning the appropriate string. No problems... however I can't find a way of changing the.
Setup must restart your computer. After restarting your computer, run Setup again to complete the installation of xxxxx
Because I am creating a runonce entry, the installer will automatically run after reboot (which it does). The text "run Setup again" is not relevant in my situation and I want to change the text to say that the installer will continue once you restart.
I have tried to find where to change this text but with no success. I assume that PreparingMemo might be the candidate but no luck or not sure how to use it. Any help would be appreciated.
See Handling and customizing errors and messages in Inno Setup.
This particular message is defined by the PrepareToInstallNeedsRestart message.
You can change it in the [Messages] section:
[Messages]
PrepareToInstallNeedsRestart=Setup must restart your computer. After restarting your computer, the Setup will continue to complete the installation of [name].%n%nWould you like to restart now?
If you need to change the message text dynamically, assign WizardForm.PreparingLabel.Caption. E.g. from CurPageChanged(wpPreparing) event.
I have created an installer using Inno Setup. The installer uses a packaged-in DLL to check availability of a specific device on the target machine. If the device is found, the installation is allowed to finish, otherwise the installation is rolled-back (rollback is done using below lines in script):
if <DeviceNotFound> then
begin
CancelWithoutPrompt := true;
WizardForm.Close;
end;
I have checked that the above check and rollback logic works fine if the setup is run with /silent cmd line param. However, when I use /silent param, the setup displays the Installation progress wizard form.
Also, I found that if I run the above setup in /verysilent mode, then the "DeviceNotFound" check logic works fine but the rollback logic doesn't work and it seems as if rollback logic doesn't get executed at all. Instead of performing rollback, the installer successfully installs.
Now, I have a requirement to run the setup silently so that no window is displayed but it must install or rollback based on device check. Therefore, I have the below queries:
Can I rollback the installer when it is running in /verysilent mode? If so, please advise how it may be achieved. I can detect verysilent install mode as shown in question:
How to detect whether the setup runs in very silent mode?
Alternatively, can I Hide/Minimize the Installation progress window when it is running in /silent mode? If so, please advise how it may be achieved.
Please help me with my above queries.
Sorry to be so descriptive but I tried to explain my problem and queries!
EDIT
I am not doing the above mentioned check in InitializeSetup(). I am doing the check from a function invoked by AfterInstall directive from [Files] section. I have a limitation that I cannot do it from InitializeSetup() as the packaged-in DLL is not extracted till [Files] section completes. I also need to run the installer in Windows PE (Preinstallation Environment), hence I cannot use ExtractTemporaryFile() function to forcefully extract the DLL because the {tmp} path is not valid in that environment. That leaves me with only one option is to check after [Files] section is done. Please advise!
Your constraint on not using ExtractTemporaryFile does not make sense.
The Inno Setup installer always creates a temporary folder for the installation.
2015-07-31 09:02:07.458 Created temporary directory: C:\Users\martin\AppData\Local\Temp\is-1CN29.tmp
If it is not possible to create the folder, the installation fails.
The Inno Setup tries to create the temporary folder in these locations:
%TMP%
%TEMP%
%USERPROFILE%
Windows installation folder (C:\Windows)
At least the last path has to exist even in the "Windows PE".
So I do not think, there's anything preventing you from using the ExtractTemporaryFile function.
I am using Inno Setup for the first time. When I start the program I am presented with a blank script page. Is scripting the only way you can create a setup package? Is there anything else?
Yes, Inno Setup is script-based (thank God -- this really makes things a lot easier if you ask me). But there is a "wizard" that lets you create a new setup by a simple step-by-step approach in a simple GUI. Simply choose "Create a new script file using the Script Wizard" in the "Welcome" dialog box that appears when you start the Inno Setup Compiler.
If you have disabled the Welcome dialog box, use File/New instead to start the wizard.
Update
I was just informed about the new InnoIDE.
Inno Setup is script based. If you want a GUI Builder then you may check the site "Third-Party Files" on Inno Setups Homepage.
The easiest way to start is with one of the example scripts included with the install.
Just change the product name in the sample and you are set for 90% of basic installs
I am using Inno Setup for the installer for my windows application. If a user has the application when the installer is run (eg. for an update), the installer will stop when it is unable to replace a file in use, and it allows the user to select whether to Abort, Ignore, or Retry.
I would like it to only allow Abort or Retry and remove the option to Ignore. Does anyone know how this can be done?
Or if this can't be done, how can I make the installer abort if the application is running?
The easy way to detect whether the application is running requires co-operation from the application, so it's best to work this out before you ship your first version. Use Inno Setup's AppMutex setting. There is an example in the Inno Setup knowledge base for setting up a mutex visible in multiple sessions. There is more about AppMutex in Inno Setup's help file.