I have a HID keyboard stack on my microcontroller, I have a question, whether HID device after plug-in obtains some information about operating system it is connected to?
Not directly, but you can figure it out in the early handshake process between the USB devices via the Configuration Descriptors.
Check out these links:
https://stackoverflow.com/a/30362736/759341
https://www.google.com/patents/US20120054372
http://www.usb.org/developers/hidpage/HID1_11.pdf
Related
I have developed a kernel driver for a USB device. Such a device has some pins that can provide functionality both as CDC ACM serial port or as input buttons. So to implement that I had to use two different USB configuration descriptors.
The driver works as expected, but I have to hardcode the chosen setup before compiling and loading the firmware to the micro-controller. I am searching a mechanism to change that device configuration from userspace.
I read about a SET_CONFIGURATION message on USB documentation, but coudn't find any Linux tool to send such kind of standard USB messages from userspace to the USB bus.
Does some of you (with more experience on this topic) know some userspace Linux tool to send a SET_CONFIGURATION message to a device connected to the USB bus?
Thanks in advance! :)
The function libusb_set_configuration() in LibUSB could do that in theory, but there is no need.
One can simply put both HID (for the button) and CDC (serial port) into one configuration using an "Interface association descriptor" (IAD).
This github repo resolves my issue:
https://github.com/avtolstoy/usbtool
No need for any special tools. You can simply do it via sysfs:
Find your device cd /sys/bus/usb/devices/X-Y/ where X is the bus number and Y is the device number.
Edit bConfigurationValue e.g., using sudoedit
Set the file contents to the desired configuration number and save it
That’s it!
I have a embedded device that runs linux 2.6.37.
I want my application to know when the USB is connected.
Currently I can achieve this by pooling
/sys/devices/platform/musb/musb-hdrc.0/vbus.
However this approach does not distinguish between a USB charger or a USB host.
I found this udev approach but I don't think it's available in my version of the kernel. because I did not find any USB related nodes in my /dev. This discussing also shows that it might not be feasible, ether.
I also found linux hotplug and tried the netlink example, but I didn't see any output running the example when I connect/disconnect the USB cable.
What I want to do is to detect connection type on the device, when USB is connected, and prepare (unmount file system) and switch to g_file_storage if device is connected to a host, and do nothing if device is connect to a charger.
How shall I achieve this?
To achieve that, you can use the inotify(7) feature, available in all linux kernels to be awaken as soon as some device node gets created in /sys.
To know what type of device you have, you have to read the usb info from proper usb ioctl call (or if you are not a kernel interface expert, using the libusb interface) to get the device vendor, device id and device class fields coming from the device. Normally, the hotplug software gets informed on these clase of events (via a special socket). The most probably reason you don't get the device properly initialized is some misconfiguration in the config files for udev system, which normally has one entry for each possible device vendor/device id pair and allows it to load the appropiate device driver to control it. The process continues with the device driver module creating dynamically the actual devices, and they'll appear in the /dev/ filesystem as a consequence of some other kernel event to udevd.
Read apropiate documents in <linux_src>/Documentation (this directory directory belongs to the linux kernel source code, so you'll probably need to install it), and udevd(8) man pages to be able to add a new usb.
On 2.6.37 kernel, this could be done by polling
/sys/devices/platform/musb-omap2430.0/musb-hdrc.0/mode
If handshake with host is successful then it will read as "peripheral", if fail it'll be "idle".
I am trying to find out a high-level overview of how the USB storage driver works in Linux. I'm looking for a simple article or even a picture/flowchart describing how it works.
Basically, I'm looking to get these questions answered:
When you plug the device into your computer, what happens? Is there a daemon that picks up on it, or does the event trigger an interrupt somewhere? Does the core USB driver read information about the device before passing control over to the USB storage driver? How does it decide what type of device it is? How does the device get mounted, and what allows it to communicate with the computer's filesystem? When I copy a file, what does the data flow look like in the kernel?
I hope the question isn't too vague - I tried Google to no avail, so I'm wondering if anyone knows any articles or diagrams that can explain this, or perhaps if they can explain it themselves without too much effort. Thanks.
No, it is a very good question.
The block writing is going in linux with the block device layer. The filesystems are working with this block dev layer.
If this layer wants to write something out, says it to the driver of the usb master device. This driver is talking with the usb controller chip of the motherboard.
This chip is very simple: the usb is practically a serial port, with a lot of extensions, mainly targeting the autoconfiguration and the power management. But basically, you can write out bytes, and read in bytes.
Your questions:
When you plug the device into your computer, what happens? Is there a daemon that picks up on it, or does the event trigger an interrupt somewhere?
The device (usb slave) says the master (in the motherboard): "I am here". The usb controller chip gets the message and says it to the kernel (normally) with an interrupt. The kernel reinitializes and rescans the usb bus, and says the udev: "here is a new 1234:5678 usb device on the usb tree 1.3.5"
"How does it decide what type of device it is?"
Usb devices have a vendor and model id, and they can say this on ask. Google for "usb ids".
"How does the device get mounted, and what allows it to communicate with the computer's filesystem?"
The kernel only loads the driver and says the udev (which is in userspace): "Here is a new block device on device number 22:16". From this, udev tries to mount this with some userspace daemon, it is already distribution-dependant.
I have been asked to figure out how to achieve bluetooth communication through an off-the-shelf dongle (in this case a dongle utilizing the Broadcom BCM2045 chip) using the FTDI Vinculum 2 (VNC2) USB controller. I have custom firmware written for the VNC2 to communicate with a generic USB device with the VNC2 acting as the host, and I can successfully read the VID and PID from the dongle as well as the USB device class, subclass, and protocol. I can also send data to the dongle using the bulk data endpoint and I believe the device is receiving though I have no way to tell at the moment.
So I believe I can communicate with the dongle, the problem is I have no idea WHAT to communicate to it in order to set it up in discoverable mode or to pair it with another discoverable device, nor how to actually transmit data through the wireless link once it is paired. I don't even know if there exists a standard communication protocol for this type of thing or if every device will be different. I have a vague understanding of the bluetooth protocol stack and it is my understanding that I won't be required to fully understand that as it should be implemented in the dongle on one end and in the android smartphone that we hope to connect to on the other end. Like I said, I can currently send data to the bulk endpoint, is it true that this endpoint is only for data transfer over the wireless link and I will need to connect to a different endpoint in order to send setup/configuration messages to the dongle?
In short, I need to know what data to send over the USB bus to control any generic bluetooth dongle if possible or at least one specific bluetooth dongle. I have a USB port sniffer but the complexity of the output while using the dongle to communicate is staggering and I doubt I'll ever figure it out.
Thank you in advance.
Bluetooth dongles communicate with host software stack using HCI (host control interface), which is defined in the Bluetooth spec. For reference, you can look at source code for the open source BlueZ stack (standard linux stack). You could run BlueZ on linux talking to your USB dongle, and use hcidump to capture actual packets going across HCI. You can also check out hcitool and hciconfig for performing specific actions.
I am wondering, do you need a specific device driver to read a usb device in Linux, or should it just be able to be read. If I connect my cell phone or iPod touch to my linux box, it is not found is /proc/partitions and thus is not a mountable device by fdisks standards, though gnomes nautilus does in fact mount the iPod but not the windows mobile touch pro cell phone.
So I am interested, If I just wanted to read a device(iPod touch) in linux, how can I do so. How can I get a hold of a descriptor of a set usb device so I can read it.
Thanks all.
You can access raw USB endpoints under /dev/usbdev. There is user-space libusb that makes it easier.
Unfortunately there is no simple concept of "just read it" for USB devices (I am assuming that you are not referring to reading and writing the data on the USB bus that make up the USB protocol). In short, you always need a device driver for accessing a USB device and it is up to the driver to implement "the abstraction" of the device used by the system (disk, serial device, etc).