Closed. This question does not meet Stack Overflow guidelines. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 9 months ago.
Improve this question
1) I've been using Ubuntu 18.04 with Windows 10 dual boot for some months now. Today suddenly my sound stopped working on Ubunutu. Activities -> Sound menu shows only "Dummy Output". All fine on Windows though.
2) Output of lsmod is:
rohit#rohitUb18043LTS:~$ lsmod | grep snd_
snd_seq_midi 20480 0
snd_seq_midi_event 16384 1 snd_seq_midi
snd_seq 69632 2 snd_seq_midi,snd_seq_midi_event
snd_rawmidi 36864 1 snd_seq_midi
snd_seq_device 16384 3 snd_seq,snd_seq_midi,snd_rawmidi
snd_soc_dmic 16384 0
snd_hda_codec_realtek 118784 0
snd_hda_codec_generic 81920 1 snd_hda_codec_realtek
ledtrig_audio 16384 2 snd_hda_codec_generic,snd_hda_codec_realtek
snd_soc_hdac_hdmi 32768 0
snd_sof_intel_hda_common 73728 1 sof_pci_dev
snd_soc_hdac_hda 24576 1 snd_sof_intel_hda_common
snd_sof_intel_hda 20480 1 snd_sof_intel_hda_common
snd_sof_intel_byt 24576 1 sof_pci_dev
snd_sof_intel_ipc 20480 1 snd_sof_intel_byt
snd_sof 98304 4 snd_sof_intel_hda_common,snd_sof_intel_byt,snd_sof_intel_ipc,sof_pci_dev
snd_sof_xtensa_dsp 16384 1 sof_pci_dev
snd_hda_ext_core 28672 4 snd_sof_intel_hda_common,snd_soc_hdac_hdmi,snd_soc_hdac_hda,snd_sof_intel_hda
snd_soc_acpi_intel_match 32768 2 snd_sof_intel_hda_common,sof_pci_dev
snd_soc_acpi 16384 2 snd_soc_acpi_intel_match,sof_pci_dev
snd_soc_core 237568 5 snd_sof,snd_sof_intel_hda_common,snd_soc_hdac_hdmi,snd_soc_hdac_hda,snd_soc_dmic
snd_compress 24576 1 snd_soc_core
ac97_bus 16384 1 snd_soc_core
snd_pcm_dmaengine 16384 1 snd_soc_core
snd_hda_codec_hdmi 57344 1
snd_hda_intel 53248 2
snd_intel_nhlt 20480 1 snd_hda_intel
snd_hda_codec 131072 5 snd_hda_codec_generic,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_realtek,snd_soc_hdac_hda
snd_hda_core 90112 10 snd_hda_codec_generic,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_ext_core,snd_hda_codec,snd_hda_codec_realtek,snd_sof_intel_hda_common,snd_soc_hdac_hdmi,snd_soc_hdac_hda,snd_sof_intel_hda
snd_hwdep 20480 1 snd_hda_codec
snd_pcm 102400 10 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_ext_core,snd_hda_codec,snd_sof,snd_sof_intel_hda_common,snd_soc_hdac_hdmi,snd_soc_core,snd_hda_core,snd_pcm_dmaengine
snd_timer 36864 2 snd_seq,snd_pcm
snd 86016 17 snd_hda_codec_generic,snd_seq,snd_seq_device,snd_hda_codec_hdmi,snd_hwdep,snd_hda_intel,snd_hda_codec,snd_hda_codec_realtek,snd_timer,snd_compress,snd_soc_core,snd_pcm,snd_rawmidi
rohit#rohitUb18043LTS:~$
3) I installed all updates from Software updater but no luck.
4) No change by using: sudo alsa force-reload
5) Looking around, found this thread: https://askubuntu.com/questions/1059619/sound-card-shown-as-dummy-output-in-ubuntu-18-04 . User says found the "active profile was off" and links to a solution on this forum (https://forums.linuxmint.com/viewtopic.php?t=268499). I am pasting the output of the four commands as per that link:
rohit#rohitUb18043LTS:~$ sudo fuser -v /dev/snd/*
[sudo] password for rohit:
USER PID ACCESS COMMAND
/dev/snd/controlC0: gdm 1505 F.... pulseaudio
rohit 1878 F.... pulseaudio
rohit#rohitUb18043LTS:~$ pacmd list-cards
1 card(s) available.
index: 0
name: <alsa_card.pci-0000_01_00.1>
driver: <module-alsa-card.c>
owner module: 7
properties:
alsa.card = "0"
alsa.card_name = "HDA NVidia"
alsa.long_card_name = "HDA NVidia at 0xb4000000 irq 17"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:01:00.1"
sysfs.path = "/devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card0"
device.bus = "pci"
device.vendor.id = "10de"
device.vendor.name = "NVIDIA Corporation"
device.product.id = "0fb9"
device.product.name = "GP107GL High Definition Audio Controller"
device.string = "0"
device.description = "GP107GL High Definition Audio Controller"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
profiles:
output:hdmi-stereo: Digital Stereo (HDMI) Output (priority 5400, available: no)
output:hdmi-surround: Digital Surround 5.1 (HDMI) Output (priority 300, available: no)
output:hdmi-surround71: Digital Surround 7.1 (HDMI) Output (priority 300, available: no)
off: Off (priority 0, available: unknown)
active profile: <off>
ports:
hdmi-output-0: HDMI / DisplayPort (priority 5900, latency offset 0 usec, available: no)
properties:
device.icon_name = "video-display"
rohit#rohitUb18043LTS:~$ pacmd list-sinks
1 sink(s) available.
* index: 0
name: <auto_null>
driver: <module-null-sink.c>
flags: DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY
state: SUSPENDED
suspend cause: IDLE
priority: 1000
volume: front-left: 65536 / 100% / 0,00 dB, front-right: 65536 / 100% / 0,00 dB
balance 0,00
base volume: 65536 / 100% / 0,00 dB
volume steps: 65537
muted: no
current latency: 0,00 ms
max request: 344 KiB
max rewind: 344 KiB
monitor source: 0
sample spec: s16le 2ch 44100Hz
channel map: front-left,front-right
Stereo
used by: 0
linked by: 0
configured latency: 0,00 ms; range is 0,50 .. 2000,00 ms
module: 15
properties:
device.description = "Dummy Output"
device.class = "abstract"
device.icon_name = "audio-card"
rohit#rohitUb18043LTS:~$ pacmd list-sink-inputs
0 sink input(s) available.
rohit#rohitUb18043LTS:~$
6) I tried the suggested command but it says "No such profile".
rohit#rohitUb18043LTS:~$ pacmd set-card-profile alsa_card.pci-0000_01_00.1 output:analog-stereo+input:analog-stereo
No such profile: output:analog-stereo+input:analog-stereo
rohit#rohitUb18043LTS:~$
Please help - how do I proceed?
Similar issue with "Dummy Sound" on Ubuntu 18.04 also with a NVIDIA card. This solved it for me:
Edit /etc/modprobe.d/alsa-base.conf as root and add options snd-hda-intel dmic_detect=0
Edit /etc/modprobe.d/blacklist.conf as root and add blacklist snd_soc_skl at the end of the file.
After making these changes, reboot your system.
More details (and credits): https://www.linuxuprising.com/2018/06/fix-no-sound-dummy-output-issue-in.html
I had the same problem, and tried the solution given by #maartenor without success.
Eventually I got the sound back by upgrading linux kernel to the last HWE stack, for me it was 4.15.0-106-generic to 5.3.0-59-generic.
The command to do this :
$ sudo apt install linux-generic-hwe-18.04
Edit the file /etc/modprobe.d/alsa-base.conf and add the following lines:
options snd-hda-intel dmic_detect=0
options snd-hda-intel model=laptop-amic enable=yes
The first line is to enable the speaker, the second for the internal microphone.
Good luck!
Got this answer from Reddit. Worked like a charm for me!
Link : https://www.reddit.com/r/linuxmint/comments/fltlrl/no_sound_on_acer_swift_3_with_kernel_53/
Try this..
Open your terminal
sudo apt update && sudo apt install alsamixer
run alsamixer in your terminal.
press arrow right til you go to sound option (if headphone go to HEADPHONES bar).
press M to unmute.
press up/down to adjust the volume.
press Esc to exit alsamixer.
Following steps worked very reliably. It does not fix the audio-losing-after-suspend issue permanently, but instantly as a command to run after back from suspend.
Use lspci to get the audio card location (0000:00:1f.3). On my machine,
$ lspci
00:1f.0 ISA bridge: Intel Corporation H110 ...
00:1f.2 Memory controller: Intel ...
00:1f.3 Audio device: Intel Corporation 100 Series/C230 Series Chipset ...
00:1f.4 SMBus: Intel Corporation 100 Series/C230 Series Chipset ...
Then, (make sure the directories below exist)
$ echo 1 | sudo tee /sys/bus/pci/devices/0000:00:1f.3/remove
$ echo 1 | sudo tee /sys/bus/pci/rescan
I believe the audio driver/hardware is stuck. So we remove the device driver, and rescan the PCI bus to get audio back.
i found answer above not work on my computer, and i solve this problem by accidient , this is script i use , most same as answer above, but at last, u need mute then unmute auidio. sleep a short moment after command is necessary here if you put script in sh file then excute it , use sh -c is for file redirection for root
REST=0.5
#make sure Audio always actived
sudo sh -c 'echo 1 >/sys/bus/pci/rescan'
sleep $REST
DEVICE_ID=$(lspci -D | grep Audio | awk '{print $1}')
sleep $REST
sudo sh -c 'echo 1 >/sys/bus/pci/devices/0000:00:1f.3/remove'
sleep $REST
sudo sh -c 'echo 1 >/sys/bus/pci/rescan'
sleep $REST
#mute then unmute to restart audio
amixer -D pulse sset Master mute
sleep $REST
amixer -D pulse sset Master unmute
I want to monitor (sniff) the traffic of my /dev/ttyUSB0 which is created by FTDI USB Serial Converter. I've written my own application in Windows and now I try to port it to linux and use /dev/tty/USB0. I want to debug the communication that actually happens.
The software strace is not an option for me because it only shows the syscalls to ioctl.
Using Windows the software "Free Serial Port Monitor" did it by sniffing COM1.
Output of dmesg:
[16975.000221] usb 7-1: new full-speed USB device number 5 using uhci_hcd
[16975.193543] usb 7-1: New USB device found, idVendor=0403, idProduct=6001
[16975.193548] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[16975.193552] usb 7-1: Product: FT232R USB UART
[16975.193555] usb 7-1: Manufacturer: FTDI
[16975.193558] usb 7-1: SerialNumber: A400BJII
[16975.200550] ftdi_sio 7-1:1.0: FTDI USB Serial Device converter detected
[16975.200599] usb 7-1: Detected FT232RL
[16975.202604] usb 7-1: FTDI USB Serial Device converter now attached to ttyUSB0
However I tried moserial to do this and the command "echo foobar > /dev/ttyUSB0" to verify, if it works. Also my software doesn't create an output to moserial.
UPDATE:
Found out how to monitor usb directly, now I need to convert USB packets to RS-232 (what FTDI basically does).
Setup usbmon
modprobe usbmon
1.1 With Linux kernels prior to 2.6.23, you will also need to run this command
modprobe -t debugfs none /sys/kernel/debug
usbmon0 will monitor any traffic from all usbmon0 to usbmonX
2.1. Find the correct usb device
cat /sys/kernel/debug/usb/devices|grep FTDI -A 7 -B 4
T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 12 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0403 ProdID=6001 Rev= 6.00
S: Manufacturer=FTDI
S: Product=FT232R USB UART
S: SerialNumber=A400BJII
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 90mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=ftdi_sio
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
2.2. Note Bus number of the port (Bus=07), so usbmon to monitor will be usbmon7
2.3. Use wireshark to capture the usbmon7 interface or use following command to get output to the console (stdout) ... replace the number with bus-id
cat /sys/kernel/debug/usb/usbmon/7u
What means 'u'?
https://www.kernel.org/doc/Documentation/usb/usbmon.txt
Two formats are supported currently: the original, or '1t' format, and the '1u' format. The '1t' format is deprecated in kernel 2.6.21. The '1u' format adds a few fields, such as ISO frame descriptors, interval, etc. It produces slightly longer lines, but otherwise is a perfect superset of '1t' format.
How do I convert the USB capture to RS-232 capture?
I don't know it ... TODO
With your hint I managed to solve my problem, so there it is my hint for the last point:
Using Wireshark, open usbmon0 and use this filter
usb.capdata or at
Issuing two times the command echo asd > /dev/ttyUSB0 produces the result below in Wireshark
You can extract the whole Leftover Capture Data from a capture file using tshark:
tshark -r capture.pcapng -T fields -e usb.capdata
I have a CORE9G25-CON (256MBRAM) (http://armdevs.com/core9g25.html) device with embedded linux installed on it.
The version of linux is:
# uname -or
3.6.9 GNU/Linux
# cat /etc/os-release
NAME=Buildroot
VERSION=2012.11.1-dirty
ID=buildroot
VERSION_ID=2012.11.1
PRETTY_NAME="Buildroot 2012.11.1
The device is equipped with USB host connector in which I connected an USB-AUDIO interface
The USB interface is recognize by the system
# cat /proc/asound/cards
0 [Device ]: USB-Audio - USB PnP Sound Device
C-Media Electronics Inc. USB PnP Sound Device at usb-at91-1, full speed
# cat /proc/asound/devices
0: [ 0] : control
16: [ 0- 0]: digital audio playback
24: [ 0- 0]: digital audio capture
33: : timer
# ls /dev/snd
controlC0 pcmC0D0c pcmC0D0p timer
I would like to handle the AUDIO interface by using ALSA but this is the error shown on the console by using the simple command aplay -l
# aplay -l
**** List of PLAYBACK Hardware Devices ****
ALSA lib control.c:739:(snd_ctl_open_noupdate) Invalid CTL hw:0
aplay: device_list:226: control open (0): No such file or directory
aplay: conf.c:3095: snd_config_update_free: Assertion `update->count > 0 && update->finfo' failed.
Aborted
I googled for about a week trying to fix the problem but, up to now, i didn't find any solution.
Could you help me to fix the problem ?
Had you other similar experience about it ?
Thank you very much for your help and cooperation
best regards
What does your alsa.conf look like ? do this
locate alsa.conf
typically found at
/usr/share/alsa/alsa.conf
do a google on
audio sound alsa Invalid CTL hw:0
this might get you on the right path
#alsa.conf minimal configuration
ctl.hw {
#args [ CARD ]
#args.CARD {
type string
}
type hw
card $CARD #with 0 alsamixer work, with $CARD alsamixer lend to invalid argument
}
I installed raspbian using noobs on a fresh SD card.
I have XBian with XBMC in another SD and it works so HW is Ok.
The problem is that I cannot play stereo, thus I cannot play through HDMI, and I cannot play from ZynAddSubFX that is a midi sampler and my final target for this project.
This is the result from amixer:
Simple mixer control 'PCM',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum
Playback channels: Mono
Limits: Playback -10239 - 400
Mono: Playback -1900 [78%] [-19.00dB] [on]
the Mono playback is weird for me and the Limites of the playback are also suspicious.
If I install pulseaudio then amixer takes A LOT OF TIME to respond BUT this is the result:
amixer
Simple mixer control 'Master',0
Capabilities: pvolume pswitch pswitch-joined penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 65536
Mono:
Front Left: Playback 27111 [41%] [on]
Front Right: Playback 27111 [41%] [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch cswitch-joined penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 65536
Front Left: Capture 65536 [100%] [on]
Front Right: Capture 65536 [100%] [on]
Much more convenient and expected.
The problem is that I DON'T want to use pulseaudio and, actually, I think ZynAddSubFX is not compatible with pulseaudio.
For sure I've googled around a lot but there is no clear solution. I found out the trick for forcing analog output (amixer cset numId=3 1) it works in terms that I do hear something but the main problem is there .. only mono.
this is the output for lsmod:
lsmod
Module Size Used by
snd_bcm2835 16165 0
snd_soc_bcm2708_i2s 5474 0
regmap_mmio 2806 1 snd_soc_bcm2708_i2s
snd_soc_core 131268 1 snd_soc_bcm2708_i2s
regmap_spi 1897 1 snd_soc_core
snd_pcm 81593 2 snd_bcm2835,snd_soc_core
snd_page_alloc 5156 1 snd_pcm
regmap_i2c 1645 1 snd_soc_core
snd_compress 8076 1 snd_soc_core
snd_seq 53769 0
snd_timer 20133 2 snd_pcm,snd_seq
snd_seq_device 6473 1 snd_seq
leds_gpio 2059 0
led_class 3688 1 leds_gpio
snd 61291 7
snd_bcm2835,snd_soc_core,snd_timer,snd_pcm,snd_seq,snd_seq_device,snd_compress
Any clue ?? Any other output that might be interesting ??
I'm using Debian 4.4.6-1+rpi14 (2016-05-05) and have a very similar problem. The sound is mono only when using ALSA. The the sound is not continuous and the quality is poor. If I use omxplayer the output is stereo and the sound quality is good. I've found if I use mplayer -ao alsa:device=hw=0,0 then the sound quality is as good as using omxplayer and it is stereo! Somehow ALSA is not functioning normally if the default device hw:0.0 is not given as an parameter. So the solution for pulseaudio is to add the the device=hw:0,0 option.
pactl load-module module-alsa-sink device="hw:0,0"
pactl set-default-sink alsa_output.hw_0_0
Now pulseaudio shows stereo output and the sound quality is as good as omxplayer.
I finally "solved" by buying a 1.34€ USB sound card. I dont really thing that this count as a solution but .. I needed the mic line anyhow
Late answer but I can still relevant at this date: I faced the same problem (mono sound through hdmi output) with the ubuntu distro for raspberry pi, but everything works fine when using the raspbian distro from raspberry web site.
I'm running Ubuntu 12.04 studio on a HP Pavilion dm1 4200sg netbook. It's pretty much a fresh install. I try to start jackd server by running
jackd -R -d alsa
and it fails with output:
JACK server starting in realtime mode with priority 10
control device hw:0
control device hw:0
audio_reservation_init
Acquire audio card Audio0
creating alsa driver ... hw:0|hw:0|1024|2|48000|0|0|nomon|swmeter|-|32bit
control device hw:0
ALSA: Cannot open PCM device alsa_pcm for playback. Falling back to capture-only mode
Cannot initialize driver
JackServer::Open() failed with -1
Failed to open server
Running aplay -l gives the following output:
**** List of PLAYBACK Hardware Devices ****
card 0: Generic [HD-Audio Generic], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: SB [HDA ATI SB], device 0: STAC92xx Analog [STAC92xx Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
I find that by running
jackd -R -d alsa -d hw:1
jackd starts successfully. I would like to configure my machine so that hw:1 is the default option (i.e. to make the original 'jackd -R -d alsa' command work). Can anyone help me to do this?
I've tried editing ~/.asoundrc to be
pcm.!default {
type hw
card 1
}
ctl.!default {
type hw
card 1
}
but this doesn't seem to work. I'm well out of my comfort zone here and any help would be appreciated. Thanks!
I've found a workaround. It doesn't configure JACK server but alters the order the sound cards are listed.
I first entered into the terminal:
sudo lshw -c multimedia
which showed which modules the two cards were using. They were both using 'snd-hda-intel'.
I then entered into the terminal:
cat /proc/asound/card0/id
cat /proc/asound/card1/id
Which gave ids 'Generic' and 'SB' for cards 0 and 1, respectively.
I then added the following two lines to the end of the file '/etc/modprobe.d/alsa-base.conf'
options snd-hda-intel id=SB index=0
options snd-hda-intel id=Generic index=1
After rebooting the machine, card 'SB' was loaded into position 0 and
jackd -R -d alsa
correctly started.
First, in a terminal window, run this command:
cat /proc/asound/cards.
You’ll see output a bit like this:
0 [SB ]: HDA-Intel - HDA ATI SB
HDA ATI SB at 0xfcef8000 irq 16
1 [DSP ]: H-DSP - Hammerfall DSP
RME Hammerfall DSP + Digiface at 0xfcff0000, irq 20
2 [NVidia ]: HDA-Intel - HDA NVidia
HDA NVidia at 0xfe57c000 irq 32
The “name” of each soundcard is in square brackets.
With this information, you can now refer to a particular device as, for example hw:DSP now you can execute the command:
jackd -d alsa -d hw:DSP
And thats all, taken from:
http://www.jackaudio.org/faq/device_naming.html
EDIT: added code tags
First, open up alsa-base.conf:
sudo gedit /etc/modprobe.d/alsa-base.conf
Find the following line:
"options snd-hda-intel index=-2"
And change it to:
"#options snd-hda-intel index=-2"
Restart your machine and try again. You may have to set the proper sound device (alsa) for your programs.