As far as I figured out, Raspberry pi 3 which runs DP 4.1 cannot get IP address from my switch. Other devices on switch like PC's running windows or Rasbian installed Rasberries can get IP address as it should and be able to communicate each other. I tested my pi with both WiFi and cable connected router and it was able to get IP address normally. So I'm nearly sure that there is no problem on my Ethernet cable, pi or switch.
As a last note, the switches is Cisco sg100d-05 and I cannot use a router instead of this switch.
Is there anything that I can do to join this closed network on switch?
Related
I installed a PPP (Point to Point Protocol) in my Raspberry pi in order to connect with another Linux based card using serial port (with USB-RS422 cable). The PPP is well installed and configured, so from the raspberry pi I can ping the Linux card, my goal is to access the Linux card through the raspberry pi, I active the port forwarding in my raspberry pi also I added a route in my PC (Windows based).
For information, my PC is under my company network, the raspberry is under an IoT device network managed also by my company. Please have a look at the below diagram to well understood the situation.
enter image description here
My Question is : Do you have any idea to how can I access the based Linux
Card through the raspberry pi? Should I use nftables for that? if yes how? any other suggestions?
To clarify more, I changed the design, which means I connect my raspberry pi to my pc using ethernet cable and tried to ping the based card through the raspberry pi, it works well, means that I could ping the based card from my pc. Please have a look at the below picture:
enter image description here
I have an Android tablet and A Raspberry Pi and I want to established a connection between them automatically when the tablet sends a request to the Pi.
I followed an Android application example here and start discovering any nearby devices. (https://www.youtube.com/watch?v=qnY97iBxp30)
At the same time i run sudo wpa_cli and p2p_find 20. The Android application detects the Pi, and I try to establish connection with the Pi which will display
<3>P2P-GO-NEG-REQUEST TABLET_MAC_ADDRESS dev_passwd_id=4
Normally I would just p2p_connect TABLET_MAC_ADDRESS pbc to successfully connect them together but I find it inefficient if I were to swap to another mobile device.
Are there any other ways to connect the tablet without writing the tablet mac address? For example connecting to that specific device ssid when they send a P2P-GO-NEG-REQUEST to the pi?
TL;DR Nope.
If we look at the OSI ISO 7 layer model for network communication we can see that the Media Access Control (MAC) address is vital for identifying which device is which within a wifi network.
You could try setting up a bluetooth connection or a token-ring, but I suspect that would be more effort than you are looking for.
With IPv6 your devices could use neighbour discovery to automate past the MAC entry to the Internet Protocol, and its possible to connect between devices using their link-local address (fe80::some:thing)
Wifi carries packets of data, that have addresses. By analogy, if I tell you which town I live in, but don't write my building address on the packet, you are going to have a hard time delivering it.
what I want to do :
use Raspi zero & wifi dongle to build a access point, so that other device like smart phone or PC can access to rasperry pi directly.
image in my mind is like this :
internet >> wifi router >> raspberry pi zero >> other device
what I used:
raspberry pi zero
WIFI dongle buffalo wli-uc-gnm2 (http://buffalo.jp/product/wireless-lan/client/wli-uc-gnm2)
I follow these processes:
use rasp-pi 3 as access point
use rasp-pi 2 and 2 wifi dongles as a router (http://qiita.com/mt08/items/4247894833bd4dcb27e2#_reference-27aa37c4be7f602667ff)
In the 2 instrument, with 2 dongles raspi can link to the wifi router, at the same time be an access point.
My question is can I use 1 wifi dongle to do the same thing, since buffalo wifi dongle has the ability to be AP and like to wifi router at the same time, but I cant find the instrument their site, the driver is only for windows PC.
any advice for linux environment todo that ??
I don't know if it's possible to achieve this with only 1 wifi dongle and I'm not even sure if it's possible with 2 since the only way I am aware of to set up a Pi as an AP is to connect it to your router via Ethernet and connect devices to your Pi via Wifi. But either way, isn't it possible to use a usb-hub on the Pi zero and then use 2 Wifi dongles or 1 Wifi dongle + Usb to Ethernet?
And to set up things I'd recommend: https://www.maketecheasier.com/set-up-raspberry-pi-as-wireless-access-point/
I would like to share a internet connection to a computer which is connected to Raspberry Pi 3 via ethernet cable. I am using WIFI connection for my Raspberry.
I have already set the IP settings on other computer but it does not work like when you are connecting two computers.
I need static IP on Raspberry and on other computer. I have already set that Raspberry has static IP (wlan0), but when I set ethernet (eth0) to static IP, internet on Raspberry stops working.
That is how my network should be
ifconfig from Raspberry
Thank you for your help, BR Matevz
I suggest you need to use a network range for the network between the computer and the Raspberry pi. The network between the router and Raspberry is 192.168.50.0/24
The network between the computer should be something different, for example it could be: 192.168.51.0/24
The Raspberry pi could then be 192.168.51.1 and the computer could be 192.168.51.2
You would then have to use IP forwarding on the PI and possibly NAT as well.
I've been having problems with a project of mine. I had a raspberry pi connected to webcams but I found that this was too much load for the RPI. This is why I decided to purchase and use an IP camera. The only problem though, is that the IP camera does not get wifi reception where the it should be placed but I have a powerful Directional antenna which I can attach to the RPI. I want the RPI to route internet traffic from the camera plugged into ethernet, over the wifi. I'm not one hundred percent sure how to do this but so far I have giving the wifi priority over the Ethernet and set up a dhcp server so that the camera gets an ip address.
In my current setup, when I am hard-wired into the Raspberry pi, I can connect to the camera (on 192.168.2.10) but outside, I can only connect to the web server which is also running on on the RPI. I'm not sure if the port forwarding of the camera works but I want to be able to access the webserver on 192.168.1.117 (this works) and I want to see the camera on 192.168.1.117:10 (this does not work). To try to do this, I followed this tutorial but I cant seem to get any results after finishing it.
Any help is greatly appreciated! thanks.
You may want to try UV4L with the mjpegstream driver. It turns your IP camera into a (virtual) Video device available on your RPi. An example is here (in step 3 pass the URL of your IP camera stream).