Setup Jupyter inside Fusion's CentOS 7 - linux

Question

I am trying to install Jupyter inside CentOS 7 VM (that I already had) so I can access it via port 8888 at my host Mac laptop. However, I cannot figure out the networking piece.
I am changing the IP address to 200.100.x.x for convenience
From Host Machine
I have 2 adapters for that CentOS VM
$ ifconfig gives me this (I believe those are the same):
vmnet1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:50:56:c0:00:01
inet 200.100.42.1 netmask 0xffffff00 broadcast 200.100.42.255
vmnet8: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:50:56:c0:00:08
inet 200.100.40.1 netmask 0xffffff00 broadcast 200.100.40.255
From within CentOS
[root#localhost ~]# ifconfig
eno16777736: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 200.100.40.145 netmask 255.255.255.0 broadcast 200.100.40.255
inet6 fe80::20c:29ff:febf:4878 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:bf:48:78 txqueuelen 1000 (Ethernet)
RX packets 645 bytes 97963 (95.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 215 bytes 24854 (24.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
eno33554984: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 200.100.42.128 netmask 255.255.255.0 broadcast 200.100.42.255
inet6 fe80::250:56ff:fe3d:7210 prefixlen 64 scopeid 0x20<link>
ether 00:50:56:3d:72:10 txqueuelen 1000 (Ethernet)
RX packets 18 bytes 1884 (1.8 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 45 bytes 6130 (5.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 220 bytes 50398 (49.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 220 bytes 50398 (49.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
My tests
I pinged the following IP addresses from my host machine and they all worked:
200.100.42.128
200.100.40.145
200.100.42.1
200.100.40.1
That means there is networking connectivity into the VM. Correct?
When I do jupyter notebook, I could access http://localhost:8888/tree inside the VM but I cannot go there using any IP address from my host OS on the Macbook.
I have restarted my VM many times.
Questions
Is it because of port blocking / not forwarding (8888) or something and if so, how to fix it?
Did I setup the networking incorrectly? Is there something else I need to do inside CentOS? I read this blog here http://twiki.org/cgi-bin/view/Blog/BlogEntry201310x2 and I don't see eth0 at all.

Answer 1

The problem is Jupyter picked 127.0.0.0 or localhost by default. If you have the adapter with other IP addresses, it won't work.
You need to change the IP of Jupyter inside the VM
http://jupyter-notebook.readthedocs.org/en/latest/config.html
$ jupyter notebook --generate-config
Edit it:
vi /root/.jupyter/jupyter_notebook_config.py
Then change:
c.Notebookapp.ip = '0.0.0.0'
Restart jupyter notebook and should be good to go.
Make sure firewall is off or open for port 8888 as well.